background image

®

Model No. CI-6537

Force Sensor

5

Equipment Setup

Mounting the Force Sensor on a PASCO Dynamics Cart

The Force Sensor has two built-in mounting screws that align with the 
threaded holes in the accessory tray of a PASCO Dynamics Cart (such 
as the ME-9430 Plunger Cart or ME-9454 Collision Cart). The screws 
are spring loaded so they remain in a retracted position when not in 
use.

1. 

Position the sensor lengthwise it in the accessory tray of the Dynamics 
Cart.

2. 

Insert a size #0 Phillips head screwdriver into the threaded hole in 

the accessory tray of the Force Sensor, and align the screwdriver 
with the Phillips head screw. 

3. 

Press down with the screwdriver until the screw extends into the 

threaded hole on the dynamics car or cart.

4. 

Turn the screwdriver clockwise until the screw is tight. Repeat the 

process with the other screw. 

To mount other accessories (e.g. ME-9481 Bernoulli Cart Accessory) 
on top of the Force Sensor, attach the accessory in the Force Sensor 
accessory tray in the same way you would attach the accessory to a 
Dynamics Cart.

Mounting the Force Sensor on a Support Rod

The Force Sensor has a hole and thumbscrew at one end that allows 
you to mount the sensor on a support rod from 3/8” to 1/2” diameter. 

T

A R E

Figure 2:  Mounting the sensor on the Dynamics Cart

Summary of Contents for CI-6537



















Reviews: