background image

 

 

18)

 

Install dual binding posts through the 2 holes in each vertical internal baffle from inside the 

main enclosure using 1 of the binding post spacers for each pair. On the inside of each sub-enclosure 
place the ring terminals attached to the 6" red/black speaker wires to the matching red and black 
binding posts and secure with the supplied nuts (no binding post spacer should be used inside the 
sub-enclosures). Tighten each nut securely using an 8 mm (5/16") wrench.

 

 

 

19)

 

Cut 3 x 3" pieces of speaker gasket tape, peel off the adhesive covering, and place on the bottom 

panel on the inside of the enclosure centered between the 4 pre-drilled screw holes. Insert the 3 x 

18650 

2600mAh Li-Ion Flat Top Batteries into the Dayton Audio LBB-3 3 x 18650 Lithium Battery Charger 
Board/Module (be sure to ensure the polarity is correct). Place the battery charger board on the gasket 
tape with the battery side down. Secure the battery board into position using 4 x #6 x 1-1/2" Coarse 
Thread Cabinet Screws and 4 x nylon washers through the holes in each corner of the battery board into 
the pre-drilled holes in the bottom panel. Tighten the screws until the battery board is firmly held in 
place compressing the gasket tape, this will keep the battery board from rattling while locking the 
batteries in place.

 

 

Summary of Contents for Blast Box




















Reviews: