Partner 1750 Operator'S Manual Download Page 7

ENGLISH

7

DAILY INSPECTION AND MAINTENANCE

CAUTION!
Always disconnect the power before cleaning or performing maintenance.

Here are a few general instructions for maintaining your hand-

saw. If you are in doubt on any of these points, contact your 

service dealer.

1.  Inspect power cable and plug for defects.

  

A damaged power cable or plug must be replaced.

2.  Clean ventilation openings and keep them open.

3.  Check automatic chain lubrication.

4.  Turn guide bar over at regular intervals to distribute the 

wear on both sides. Check to see that the oil passage is 

clear. Clean the guide bar groove.

5.  Check chain tension, sharpen the cutters and ensure that 

chain turns easily.

6.  Check drive sprocket for abnormal wear, replacing it if 

 necessary.

7.  Remove any burrs from the edges of the guide bar

STARTING AND STOPPING

Starting

•   Grip the front handle fi rmly with your left hand.

•   Grip the rear handle fi rmly with your right hand.

•   Press and hold the power trigger lockout button with the inside of your  

 

hand and squeeze the power trigger with your index fi nger.

Stopping

Stop the saw by releasing the power trigger. If the saw does not stop,

trip the chain brake and disconnect the power cable.

CAUTION!

•   Make certain at all times that your footing is 

  secure and that the chain touches nothing
  but the wood you are cutting.

•   Keep bystanders away from your work area.

Summary of Contents for 1750

















Reviews: