Partner 1750 Operator'S Manual Download Page 2

ENGLISH

2

SYMBOLS USED IN OPERATOR’S MANUAL:

Do not use a coiled extension cord.

Minimum wire cross-section:  

1,5   mm²

Maximum cable length:  

30 m

Voltage:  

230 V

CAUTION!
Chain saws are dangerous!
Careless or improper use can 
result in severe or fatal injury.

Noise emission to the environment according to the 

 European Community’s Directive. The machine’s 

 emission is specifi ed in «TECHNICAL SPECIFICATIONS» 

page 3 and on label.

Always disconnect power before performing 

cleaning or  maintenance work.

Visual inspection.

Always use approved safety gloves.

Clean your chain saw regularly.

Use approved face mask or safety goggles.

CAUTION!

Chain saws are dangerous! Careless or im-

proper use can result in serious or fatal injury.

•   Read operating instructions carefully.

•   Always observe the «Safe Use» recommendations on page 4.

•   Check chain and guide bar for correct assembly and adjustment.

•   Start the saw.

•   Do not start sawing until an adequate amount of oil has

 

reached the chain.

•   Incorrect chain tensioning increases wear on chain, sprocket

 

and guide bar, and may result in damage to these parts.

•   Improper use of power cable may lead to serious motor damage.

IMPORTANT! BEFORE USING CHAIN SAW

CAUTION!
The chain saw must not be modi

fi

 ed in any way under any circumstances without the permission of the manufacturer. 

Use only original accessories. Unauthorized modi

fi

 cations and/or accessories may cause serious or fatal injury of the 

operator or others.

Minimum wire cross-section:  

1,5  mm²

Maximum cable length:  

30  m

Voltage:  

230   V

IMPORTANT!

Do not use a coiled

power cable!

Read operating instructions and make  certain you 

understand them thoroughly before using the chain 

saw.

Always use:

•   Approved helmet

•   Approved hearing protection

•  Approved safety goggles or face mask

The chain saw is double-insulated.

This product conforms to

applicable CE directives.

Do not expose saw to rain or moisture.

Disconnect power in case of damage to power cable.

Maximum permissible guide bar length.

SYMBOLS ON THE CHAIN SAW:

This product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the  recycling 

of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative 

 consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.

For more detailed information about recycling of this product, please contact your local council offi ce, your household waste disposal 

service or the shop where you purchased the product.

Summary of Contents for 1750

















Reviews: