background image

 

 

10. Set unlock time 

Setting of the unlock time is indicated in seconds from 00 to 99. The setting 02 will be equal to 2 

seconds unlock. If 00 is set, the controller will be unlocked by the card and wait for any other card 

to be read to block. 
To change the unlock time, put the controller in setup mode. In this mode, the controller keyboard 

flashes slowly, the controller waits for a command to be entered. 
To set the unlock time: press “4” (the device’s keyboard starts flashing quickly) + “02” (enter the 

unlock time in seconds) + “#” to confirm the unlock time, the controller will emit two short beeps: 

 

 

 

Command: 

“4”

 + 

“03”

 + 

“#”

 

 

11. Security Modes setting 

The built-in controller can operate in one of three modes: 

1.

 

The controller accepts and unlocks only by cards added to memory. 

Mode code "00”.

 

2.

 

The controller accepts and unlocks by cards or a PIN code. 

Mode code “01”

3.

 

The controller accepts and unlocks only by cards and then entering the PIN code for this card. 

Mode code 

"02".

 

To change the operating mode, put the controller in setup mode. In this mode, the controller 

keyboard flashes slowly, the controller waits for a command to be entered. 
To set the desired mode: press “3” (the device’s keyboard starts flashing quickly) + “00” (operating 

mode - only on cards) + “#” to confirm the setting, the controller will emit two short beeps: 

 

 

 

Command: 

“3”

 + 

“00”

 + 

“#”

 (

by card)

 

Command: 

“3”

 + 

“01”

 + 

“#”

 (

by card or PIN code)

 

Command: 

“3”

 + 

“02”

 + 

“#’

 

(by card and PIN code)

 

The controller supports access card locking mode. When the lock mode is on, using the same access 

card for 5 minutes or entering the wrong password for the access card 10 times in a row will cause 

the controller to lock for 2 minutes. During this time, the controller stops accepting cards and 

passwords, the call button is locked and does not respond to pressing or touching. After 2 minutes, 

the controller returns to normal operation.  
The mode codes are: “lock is disabled” is 

“00”

, “lock is enabled” is 

“01”

.

 

 

 

Summary of Contents for Myers D300S EK HD













Reviews: