background image

 

 

6. Master password change 

To change the master password, put the controller in setup mode. In this mode, the controller 

keyboard flashes slowly, the controller waits for a command to be entered. 
To change the master password: press “0” (the device’s keyboard starts flashing quickly) + “77” + “#” 

+ “XXXXXX” (a new 6-digit master password) + “#” + “XXXXXX” (repeat password entry) + "#". 

Command: “

0”

 + “

77”

 + “

#”

 + “

XXXXXX”

 + “

#”

 + “

XXXXXX”

 + “

#” 

 

7. General unlock password change 

To change general unlock password, put the controller in setup mode. In this mode, the controller 

keyboard flashes slowly, the controller waits for a command to be entered. 
To change the general unlock password: press “0” (the device’s keyboard starts to flash quickly) + 

“11” + “#” + “NNNNNN” (new password of 6 digits) + “#” + “NNNNNN” (repeat new password) + “#”. 

Command: “

0”

 + “

11”

 + “

#”

 + “

XXXXXX”

 + “

#” 

+ “

XXXXXX”

 + “

#” 

 

8. Reset to factory settings 

To reset to factory settings, put the controller in setup mode. In this mode, the controller keyboard 

flashes slowly, the controller waits for a command to be entered. 
To reset to factory settings: press “0” (keyboard device starts flashing quickly) + “99” + “#”.  

As a confirmation of the reset, the controller emits one short beep and remains in setup mode 

waiting for settings. 

Command: “

0”

 + “

99”

 + “

#”

 

Resetting to factory settings does not delete the added access cards from the controller memory! 

 

9. Access cards adding and deleting 

9.1. Adding access cards 

To add personal access cards, put the controller in setup mode. In this mode, the controller 

keyboard flashes slowly, the controller waits for a command to be entered. 
To add a user card: press “1” (the device’s keyboard starts flashing quickly) + “YYY” (card serial 

number) + “#” + scan the card by the built-in reader.  
If the card is added successfully, the controller will emit two short beeps:  

 

 

 

If the card was added earlier or an error was made while entering a command, the controller will 

emit four short beeps error signal:  

Summary of Contents for Myers D300S EK HD













Reviews: