background image

est susceptible d'en compromettre le fonctionnement.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

This device and its antenna(s) must not be co-located or operating in conjunction with any other
antenna or transmitter, except tested built-in radios.

Cet appareil et son antenne ne doivent pas être situés ou fonctionner en conjonction avec une
autre antenne ou un autre émetteur, exception faites des radios intégrées qui ont été testées.

This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.

Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20
cm de distance entre la source de rayonnement et votre corps.

We, Particle Industries, Inc., declare under our sole responsibility that the product,
MON524E01C01KIT, to which this declaration relates, is in conformity with RED Directive 2014/53/EU
and (EU) 2015/863 RoHS Directive 2011/65/EU (Recast).

The full text of the EU declaration of conformity is available at the following Internet address

https://www.particle.io/

.

Radiation Exposure Statement: This equipment complies with radiation exposure limits set forth
for an uncontrolled environment.

The operating frequency bands and the maximum transmitted power limit are listed below:

BLE 2402-2480MHz, 10dBm
Wi-Fi 2.4GHz band 2412-2484MHz, 21.5dBm
LTE B1 B3 B7 B8 B20 B28 704.5-959.3MHz 1710.7-2687.5 MHz, 25dBm
WCDMA 882.4-957.6 MHz 1922.6-2167.4 MHz, 25dBm

UKCA Conformity:

Radio Equipment Regulations 2017 (S.I. 2017/1206)

EU DECLARATION OF CONFORMITY

UNITED KINGDOM

Summary of Contents for Monitor One














































Reviews: