manualshive.com logo in svg

Partec CyFlow Cube Series, Instrument Operating Manual

Share
Download
Partec CyFlow Cube Series Instrument Operating Manual Download Page 30

CyFlow

®

 Cube Instrument Operating Manual 

Rev018_2012-01-27 

30/36 

Transport and Storage 

For the transport of the system to a different location it will be necessary to disconnect all external data and 
supply connections. In case of use with potentially bio-hazardous material, please see Partec standard 
operating procedure (SOP) for decontamination. The system should be carried in upright position. During 
transport or storage please take care that the system will be stored under the following conditions: 

Temperature 

5-50

°

C 

Humidity 

20-85% relative (non-condensing) 

Room   

Clean environment, no direct sun light 

 

Disposal 

 

 

 
In case of product disposal, please proceed according to the Partec standard operating procedure (SOP) 
for decontamination. 

After decontamination, the system has to be disposed according to the local regulations and laws.  

For further information, please contact your local distributor or Partec.

 

 

 

 

 

 

 

 

 

 

 

 

Warning: The Waste may contain biohazardous and carcinogenic 
material from the samples (infectious material, dyes). 

Summary of Contents for CyFlow Cube Series





































Reviews:

No comments

Brands by name

Popular brands

Load more brands