114
18.
Remove the needle bearing from the underwater unit.
19.
Remove the oil seal and plane thrust bearing of the drive shaft seat, and remove the
drive shaft shim and needle roller bearing.
Propeller shaft and clutch block
1.
Check the claw clutch; If broken or damaged, replace it.
2.
Check the propeller shaft; Replace it if worn or bent.
Install the claw clutch
1.
Fit the bearing ball (large) and clutch spring into the hole of shift plunger.
2.
Place four bearing balls (small) in the corresponding holes of the shift plunger and
insert them into the propeller shaft.
3.
Install the claw clutch. "F" or "●" faces the forward direction of the engine. Fix the
clutch pin.
Note:
The figure shows the propeller shaft of forward-rotating model; The claw clutch
installation method of the backward-rotating model is the same as that of the
forward-rotating model.
4.
Install clutch spring ring.
Housing cover of underwater unit
1.
Check the bearing for rust and whether there is noise during rotation; If so, replace it.
2.
Remove the bearing and oil seal with bearing puller.
Note:
Do not remove the bearing unless it needs to be replaced.
3.
Remove the needle bearing with special tool.
Note:
When reinstalling the oil seal and needle bearing, please use new parts to replace
them.
4.
Clean the housing cover with a soft brush and solvent.
5.
Check the housing cover; Replace it if cracked or damaged.
Install the oil seal and bearing of the housing cover
1.
Install the oil seal.
2.
Fit the new bearing on the reverse gear.
Note:
Use special tools to install the oil seal and bearing.
Pay attention to the installation direction and depth.
Make sure that the manufacturer's mark of the bearing faces the reverse gear.
Mounting depth:
Summary of Contents for F115 BEX-T
