![background image](http://html1.mh-extra.com/html/parkside/pof-1300/pof-1300_operation-and-safety-notes_3813887005.webp)
7
GB/IE/CY
Introduction
14
Fine adjustment knob for depth of cut
Figure B, rear of device:
15
Clamping lever
16
Markings for zero-reset
17
Lights for cutting area
18
Tightening nut with integrated 6mm collet
19
Tightening nut with integrated 8mm collet
20
Router bit
21
Locking screw
22
Guide rail
23
ON/OFF switch
24
Safety lock-out
25
Thumbwheel for speed preselection
Figure C:
26
Guide rod for guide fence
27
Guide fence
28
Screw for the fine adjustment of the guide fence
29
Stirrup for the fine adjustment of the guide fence
Figure D:
30
Screw for attaching the vacuum extraction
adapter
31
Vacuum extraction adapter
32
Reducer piece
Figure E:
33
Centring pin
34
Wing nut for centring pin
35
Guide bushing
36
Guide bushing ring
37
Spanner
Q
Included items
1 Carrying case
1 Router POF 1300
1 Tightening nut with integrated 6mm collet
1 Tightening nut with integrated 8mm collet
1 Router bit set (10-piece)
1 Spanner (for tightening nuts
18
+
19
) (see Fig. E)
1 Guide bushing (see Fig. E)
1 Guide fence (see Fig. C)
1 Vacuum extraction adapter (incl. screws) (see Fig. D)
1 Reducer piece
1 Centring pin (see Fig. E)
1 Operating instructions
1 Booklet covering “Warranty and service”
Q
Technical information
Rated voltage:
230 V ~ 50 Hz
Nom. power input:
1300 W
No-load speed:
n
0
11000 - 28000 min
-1
Tool holder:
6 / 8mm
Plunge depth:
max. 55mm
Protection class:
II /
&
Noise and vibration data:
Values determined in accordance with EN 60745
The sound pressure level (A-weighted) of the
device is typically 95 dB (A). Uncertainty K=3 dB.
The sound level while working can exceed
106 dB (A).
Wear ear protection!
Evaluated acceleration, typical:
Hand / arm vibration a
h
= 12,065 m / s
2
Uncertainty K = 1,744 m / s
2
WARNINg!
The vibration level given in
these instructions has been measured in accord-
ance with a standardised measurement procedure
specified in EN 60745 and can be used to com-
pare devices. Different uses of the device give rise
to different vibration levels and in many cases they
may exceed the values given in these instructions. It
is easy to underestimate the vibration load if the elec-
trical power tool is used regularly in particular cir-
cumstances.
Note:
If you wish to make an accurate assessment
of the vibration loads experienced during a particular
period of working, you should also take into account
the intervening periods of time when the device is
switched off or is running but is not actually in use.
This can result in a much lower vibration load over
the whole of the period of working.
Summary of Contents for POF 1300
