![background image](http://html1.mh-extra.com/html/parkside/pof-1300/pof-1300_operation-and-safety-notes_3813887014.webp)
16 GB/IE/CY
Operation / Maintenance and cleaning / Disposal
j
Place the guide fence
27
against the edge of
the workpiece. Now carry out the fine adjust-
ment. Turning the screw for the fine adjustment
28
of the guide fence clockwise reduces the
distance. Turning the screw for the fine adjustment
28
of the guide fence anticlockwise increases the
distance. The stirrup
29
for the fine adjustment
of the guide fence indicates the corrections on
the scale.
j
After the device has been lowered, apply the
clamping lever
15
by turning it anticlockwise.
j
Carry out the routing process using uniform
speed and pressure (see Figs. F, G).
j
After the routing process lift the device from the
workpiece and switch it off.
Q
Routing a circular arc
profile / Fig. H
j
Reverse the guide fence
27
(stop edge faces
upwards) and push it into the guide rails
22
of
the base plate
5
. Fasten it in place with the
locking screws
21
.
j
Now screw the centring pin
33
with the wing
nut
34
for centring pin through the outer hole
of the guide fence
27
. Use the small recess at
the side of the spanner
37
to provide counter
pressure.
j
Insert the centring pin
33
into the marked centre
of the circle. Now carry out the fine adjustment.
Turning the screw for the fine adjustment of the
guide fence
28
clockwise reduces the radius.
Turning the screw for the fine adjustment of the
guide fence
28
anticlockwise increases the
radius. Notice that the stirrup
29
for the fine
adjustment of the guide fence moves with refer-
ence to the scale of the guide fence
27
during
this process.
j
Now guide the device with even speed and
pressure over the workpiece surface. Notice
that the path of guide fence
27
is controlled by
the setting on the stirrup
29
for the fine adjust-
ment of the guide fence.
j
Note:
You can make changes to the radius of
the circle to be machined by changing the
position of the guide fence
27
.
Q
Maintenance and cleaning
Q
Maintenance
j
The device requires no maintenance.
j
Have repairs carried out only by an electrical
power tool specialist or your service centre.
Q
Cleaning
m
Warning!
Pull the mains lead out of the mains
socket before you clean the device, otherwise there
may be risk of injury .
j
Always keep the device and the ventilation
slots clean, dry and free of oil or grease. Dirty
devices increase the risk of injury (e.g. by slip-
ping). You will work better and more safely with
clean cutting tools.
j
Do not allow any liquids to enter the inside of
the device, otherwise there may be a risk of
electric shock. Use a dry cloth to clean the
housing.
Never use petrol, solvents or cleaning agents
that might attack plastic.
Q
Disposal
The packaging is wholly composed of
environmentally-friendly materials that can
be disposed of at a local recycling centre.
Do not dispose of electrical
power tools with the household
rubbish!
In accordance with European Directive
2002 / 96 / EC (covering waste electrical and elec-
tronic equipment) and its transposition into national
legislation, worn out electrical power tools must be
collected separately and taken for environmentally
compatible recycling.
Contact your local refuse disposal authority for
more details of how to dispose of your worn out
electrical devices.
Summary of Contents for POF 1300
