Parkside PMNF 1500 A1, Translation Of The Original Instructions

Page: 31 / 156

GB
31
4.­ Remove­the­threaded­clamping­flange­
(16)­through­the­opening­in­the­protec-
tive­guard­(14).
5.­ Remove­the­cutting­disk­(7)­by­lifting­
and­pulling­away­the­take-up­spindle­
(15)­until­it­reaches­the­protective­
guard.
6.­ Remove­the­flange­(20)­and­the­spacer­
disks­(19)­through­the­opening­in­the­
protective­guard­(14).
7.­ Remove­the­second­cutting­disk­(7)­as­
described in point 5.
8.­ The­take-up­flange­(18)­can­be­left­on­
the­take-up­spindle­(15).­
­ If­you­remove­the­take-up­flange­(18),­
make sure to position it correctly. The
take-up­flange‘s­(18)­contouring­must­
face towards the motor. If you turn the
take-up­flange­(18),­the­take-up­spindle­
(15)­must­turn­with­it.
9.­ Position­the­desired­cutting­disk­(7)­on­
the­take-up­flange­(18).­
10. Set the desired cutting width by select
-
ing­the­spacer­disks­(19).­Push­the­
spacer­disks­onto­the­take-up­spindle­
(15).­This­is­followed­by­the­flange­
(20).­This­is­followed­by­the­second­
cutting­disk­(7).­All­separator­disks­(19)­
not used for setting the cutting width
must­be­pushed­onto­the­take-up­spin-
dle­(15)­after­the­second­cutting­disk.­
11. Reposition the threaded clamping
flange­(16)­on­the­take-up­spindle­(15).
12.­Press­the­spindle­retaining­tab­(6),­and­
turn­the­take-up­spindle­(15)­until­the­
spindle­retainer­fixes­the­take-up­spin-
dle­(15).­Retighten­the­threaded­clamp-
ing­flange­(16)­using­the­chuck­key­
(12).­You­can­now­release­the­spindle­
retaining­tab­(6).
Information on replacement:
• Never operate the device with
-
out protective equipment.
•­ Ensure­that­the­rotation­speed­
stated­on­the­grinding­disc­(7)­is­
the same or higher than the nomi
-
nal rotation speed of the device.
•­ Ensure­that­the­grinding­disc­
dimensions match those of the
device.
­ •­ Only­use­flawless­grinding­discs­
(ringing­test:­when­you­strike­the­
grinding disc with a plastic ham
-
mer,­it­results­in­a­clear­sound).­
­ •­ Never­re-drill­a­locating­hole­
which is too small to make it
larger.
• Never use separate bushings or
adapters in order to make grind
-
ing discs with a hole that is too
large­fit­the­device.
• Do not use any saw blades.
Only replace the diamond
cutting disks in pairs.
If the direction of rotation is marked
on your cutting disc, make sure that
it matches the direction of rotation
mark on the tool.
Wear protective gloves when
changing the discs in order to
avoid cutting damages.
Setting the groove depth
1.­ Release­the­retaining­screw­(17).
2.­ Set­the­scale­on­the­protective­cover­(5)­
to the required depth.
3.­ Reattach­the­protective­guard­(5)­with­
the­retaining­screw­(17).