background image

6 GB/IE

b)  

To ensure the highest level of opera-
tional safety, the disc guard cover 
must be attached to the electrical 
power tool and set in such a way that 
the smallest possible area of the 
abrasive consumable is exposed to 
the operator.

 The disc guard cover is there 

to protect the operator from pieces breaking  
off and accidental contact with the abrasive 
consumable.

c) 

 Abrasive consumables must be used 
only for their recommended purpos-
es, For example: never grind with the 
side face of a cutting disc.

 Cutting discs 

are intended for removing material using the 
edge of the disc. Sideways forces on these 
abrasive consumables can cause them to break.

d)  

Always use an undamaged mounting 
flange of the correct size and shape 
for your selected grinding disc.

 Suitable 

flanges support the grinding disc and reduce 
the chance of it breaking. Flanges for cutting 
discs are different from the flanges for other 
abrasive discs.

e) 

 Do not use chainsaw blades or serrat-
ed saw blades. 

Such insertion tools often 

cause the tool to recoil or you to lose control of 
the power tool.

   

Further special safety  
advice for disc-cutting

a)  

Avoid snagging the cutting disc and 
do not use too much contact pressure. 
Do not attempt to make excessively 
deep cuts.

 Overloading the cutting disc in-

creases the load and the tendency of the disc 
to twist or snag in the cut, making kickback or 
disc breakage more likely.

b) 

 Avoid the area in front of or behind 
the rotating cutting disc.

 If the cutting disc 

is moving away from you at the point of con-
straint in the workpiece, then, in the event of  
a kickback, the electrical power tool and the 
rotating disc may be thrown towards you.

c)  

If the cutting disc jams or you stop 
work for a while, switch the device 

off and hold it until the disc comes to 
a complete stop. Never attempt to 
pull the still rotating cutting disc out of 
the cut as this could cause kickback.

 

Determine and rectify the reason for the jamming.

d)  

Do not switch on the device if the cut-
ting disc is in the workpiece.

 Allow the 

cutting disc to reach full speed before carefully 
continuing with the cut. Otherwise the disc 
could snag, jump out of the workpiece or 
cause a kickback.

e) 

 Support boards or workpieces whilst 
cutting to reduce the risk of kickback 
caused by a jammed cutting disc. 

Large 

workpieces may bend under their own weight. 
The workpiece must be supported to both sides 
of the cutting disc and particularly near the  
cutting disc and at the workpiece edge.

f)  

Be particularly careful when pocket 
cutting in existing walls or other areas 
where you cannot see what you are 
cutting into.

 The cutting disc plunged into 

the surface could cut through gas or water 
pipes, electricity cables or other objects and 
cause kickback.

   

Special safety advice for 
abrading using sandpaper

  

Do not use over-sized sanding sheets. 
Follow the manufacturer’s recommen-
dations for sanding sheet size.

 Sanding 

sheets that project beyond the backing pad 
could cause injury in addition to jamming, tear-
ing of the sheet or kickback.

   

Special safety  
advice for polishing

  

Do not use the polishing bonnet if it 
has any loose parts, in particular the 
fastening cords. 

Tuck the fastening cords 

away or trim them. Loose fastening cords rotat-
ing with the attachment could catch your fingers 
or become trapped in the workpiece.

Summary of Contents for PMGS 12 A1



































Reviews: