Parkside PHS 9500 A1, Operating And Safety Instructions Manual

Page: 8 / 40

4 GB/IE/NI
2. Introduction
MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
We hope your new tool brings you much enjoyment and suc-
cess.
NOTE:
According to the applicable product liability laws, the manu-
facturer of the device does not assume liability for damages
to the product or damages caused by the product that occurs
due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service techni-
cians,
• Installation and replacement of non-original spare parts,
• Application other than specified,
We recommend:
Read through the complete text in the operating instructions be-
fore installing and commissioning the device.
The operating instructions are intended to help the user to be-
come familiar with the machine and take advantage of its ap-
plication possibilities in accordance with the recommendations.
The operating instructions contain important information on
how to operate the machine safely, professionally and econom-
ically, how to avoid danger, costly repairs, reduce downtimes
and how to increase reliability and service life of the machine.
In addition to the safety regulations in the operating instruc-
tions, you have to meet the applicable regulations that apply
for the operation of the machine in your country.
Keep the operating instructions package with the machine at
all times and store it in a plastic cover to protect it from dirt and
moisture. Read the instruction manual each time before operat-
ing the machine and carefully follow its information.
The machine can only be operated by persons who were in-
structed concerning the operation of the machine and who are
informed about the associated dangers. The minimum age re-
quirement must be complied with.
In addition to the safety instructions contained in this operating
manual and the specific regulations of your country, the techni-
cal rules generally accepted for the operation of machines of
the same type must be observed.
We accept no liability for damage or accidents which arise
due to non-observance of these instructions and the safety in-
formation.
3. Device description (Fig. 1 - 5)
1. Cutting device
2. Hand guard
3. Front handhold
4. Choke
5. Cranking rope with handle
6. ON / OFF-switch
7. Throttle lock-out switch
8. Rear handle
9. Throttle trigger
10. Locking handle
11. Fuel tank cap
12. Fuel pump “Primer”
13. Zerk fitting (grease fitting)
14. Wing screw
15. Air filter cover
16. Spark plug connector
4. Scope of delivery
• Petrol hedge trimmer
• Mixing bottle (A)
• Spark plug socket spanner (B)
• Open end wrench 8/10 (C)
• Allen key S5 (D)
• Allen key S4 (E)
• Knives protection (F) (preassambled)
• Impact protector (M)
• Manual
5. Intended use
The machine meets the currently valid EU machine directive.
Before starting any work, all protective and safety devices must
be in place.
These hedge clippers have been designed to cut soft, freshly
grown hedge material. They are not suitable for cutting branch-
es, tough wood or other material to be cut.
The machine has been designed to be operated by one person.
The operator is responsible for third parties in the area of op-
erations.
All safety and hazard notices on the machine must be ob-
served.
All safety and hazard notices on the machine must be kept in a
completely legible condition.
Use the machine in a technically flawless condition only, as
well as for its intended purpose, in a safe manner and being
aware of dangers, in compliance with the operating instruc-
tions!
Disruptions which can affect safety in particular must be elimi-
nated straight away!
The manufacturer’s safety, operation and maintenance instruc-
tions as well as the technical data given in the calibrations and
dimensions must be adhered to.
Relevant accident prevention regulations and other generally
recognized safety and technical rules must also be adhered to.
The machine may only be used, maintained or repaired by
trained persons who are familiar with the machine and have
been informed about the dangers. Unauthorized modifications