9
GB/CY
22. Have your tool repaired by a
qualified person
This electric tool complies with the relevant
safety rules. Repairs should only be carried
out by qualified persons using original
spare parts, otherwise this may result in
considerable danger to the user.
Before use
Note:
Remove all packaging material from the
product.
The operator should stand in front and stay
close to the power tool to prevent overreach.
In case of blockage, switch off the appli-
ance and unplug from the mains. Then clear
the jam.
Initial use
Grinding drills
Note:
First rough grind severely damaged
drills with a grinding block.
Fully lower the brick. To do so, turn the
dial
1
all the way in the DOWN ▼
direction.
Insert the drill into the smallest drill guide
11
on the sharpener it will fit. Please refer to
the markings (3 to 12) for the exact sizes
(Ø) of the respective drill guides
11
.
Set the ON/OFF switch
4
to position „I“
to switch on the product.
Turn the dial
1
in the UP ▲ direction until
you hear a grinding noise.
Note:
The dial
1
controls the position of
the brick inside the grinding head, thus the
grinding pressure the brick applies to the
drill. The more the dial
1
is turned in the
UP ▲ direction, the greater the grinding
pressure. Be sure not to raise the brick too
high. The brick may otherwise get in contact
with the housing.
Loosely and quickly rotate the drill back
and forth about 10 times between the left
and right stop, applying light pressure
(small drills about 5 times).
Slightly pull out the drill, turn 180° around
its own axis and reinsert up to the brick.
If necessary, repeat the entire process until
both faces are sharp. Polish so the angle
( ) between the two cutting edges (b) is
118°. Both cutting edges (b) must have the
same angle to the drilling axle (a) and have
the same length for the drill to run centred
(see images below).
2
1
3
180
0
α =
118
0
(a)
(b)
(b)
Set the ON/OFF switch
4
to position „0“
to switch off the product.
Replacing the brick
RISK OF INJURY!
Al-
ways unplug from the mains before working on
the product. Replace a worn or damaged brick
(diminished, uneven grinding, broken brick).
You will need a phillips head screwdriver for
this step.
Summary of Contents for PBSG 95 C3
