Parkside PBS 350 A1, Operating And Safety Instructions Manual

Page: 23 / 36

16 GB
insofar as nothing different is specified in the operating
manual.
- Damaged switches must be replaced at a customer ser-
vice workshop.
- Do not use any faulty or damaged connection cables.
- Do not use any electric tool on which the switch cannot
be switched on and off.
21. ATTENTION!
- The use of other insertion tools and other accessories
can entail a risk of injury.
22. Have your electric tool repaired by a qualified electri-
cian
- This electric tool conforms to the applicable safety reg-
ulations. Repairs may only be performed by an elec-
trician using original spare parts. Otherwise accidents
can occur.
Additional safety instructions
• Wear safety gloves whenever you carry out any mainte-
nance work on the blade!
• When cutting round or irregularly shaped wood, use a
device to stop the workpiece from twisting.
• When cutting boards in upright position, use a device to
prevent kick-back.
• A dust extraction system designed for an air velocity of 20
m/s should be connected in order to comply with wood-
working dust emission values and to ensure reliable op-
eration.
• Give these safety regulations to all persons who work on
the machine.
• Do not use this saw to cut fire wood.
• The machine is equipped with a safety switch to prevent it
being switched on again accidentally after a power fail-
ure.
• Before you use the machine for the first time, check that
the voltage marked on the rating plate is the same as your
mains voltage.
• If you use a cable reel, the complete cable has to be
pulled off the reel.
• Persons working on the machine should not be distracted.
• Note the direction of rotation of the motor and blade.
• Never dismantle the machineʼs safety devices or put them
out of operation.
• Never cut workpieces which are too small to hold securely
in your hand.
• Never remove loose splinters, chips or jammed pieces of
wood when the saw blade is running.
• It is imperative to observe the accident prevention regula-
tions in force in your area as well as all other generally
recognized rules of safety.
• Note the information published by your professional as-
sociations.
• Adjustable protective devices have to be adjusted as close
as possible to the workpiece.
• Important! Support long workpieces (e.g. with a roller ta-
ble) to prevent them sagging at the end of a cut.
• Make sure the blade guard (4) is in its lower position when
the saw is being transported.
• Safety guards are not to be used to move or misuse the
machine.
- An additional support is necessary for long workpieces
(table, trestle, etc.) in order to prevent the machine from
tipping over.
- Always press the workpiece firmly against the working
plate and stop in order to prevent bouncing and twist-
ing of the workpiece.
13. Avoid abnormal posture
- Make sure that you have secure footing and always
maintain your balance.
- Avoid awkward hand positions in which a sudden slip
could cause one or both hands to come into contact
with the saw blade.
14. Take care of your tools
- Keep cutting tools sharp and clean in order to be able
to work better and more safely.
- Follow the instructions for lubrication and for tool re-
placement.
- Check the connection cable of the electric tool regu-
larly and have it replaced by a recognised specialist
when damaged.
- Check extension cables regularly and replace them
when damaged.
- Keep the handle dry, clean and free of oil and grease.
15. Pull the plug out of the outlet
- Never remove loose splinters, chips or jammed wood
pieces from the running saw blade.
- During non-use of the electric tool or prior to mainte-
nance and when replacing tools such as saw blades,
bits, milling heads.
- When the saw blade is blocked due to abnormal feed
force during cutting, turn the machine off and discon-
nect it from power supply. Remove the work piece and
ensure that the saw blade runs free. Turn the machine
on and start new cutting operation with reduced feed
force.
16. Do not leave a tool key inserted
- Before switching on, make sure that keys and adjusting
tools are removed.
17. Avoid inadvertent starting
- Make sure that the switch is switched off when plug-
ging the plug into an outlet.
18. Use extension cables for outdoors
- Only use approved and appropriately identified ex-
tension cables for use outdoors.
- Only use cable reels in the unrolled state.
19. Remain attentive
- Pay attention to what you are doing. Remain sensible
when working. Do not use the electric tool when you
are distracted.
20. Check the electric tool for potential damage
- Protective devices and other parts must be carefully in-
spected to ensure that they are fault-free and function
as intended prior to continued use of the electric tool.
- Check whether the moving parts function faultlessly
and do not jam or whether parts are damaged.
All parts must be correctly mounted and all conditions must
be fulfilled to ensure fault-free operation of the electric tool.
- The moving protective hood may not be fixed in the
open position.
- Damaged protective devices and parts must be prop-
erly repaired or replaced by a recognised workshop,