Parkside PAS 7.2 A1, Translation Of Original Operation Manual

Page: 14 / 20

11 PAS 7.2 A1
GB
WARNING!
The vibration level specifi ed in these instructions
has been measured in accordance with the
standardised measuring procedure specifi ed in
EN 60745 and can be used to make equipment
comparisons. The specifi ed vibration emis-
sion value can also be used to make an initial
exposure estimate. The vibration level varies in
accordance with the use of the power tool and
may be higher than the value specifi ed in these
instructions in some cases. It is easy to underes-
timate the vibration load if the electrical power
tool is used regularly in a certain manner.
Try to keep the vibration loads as low as possible.
Measures to reduce the vibration load are, e.g.
wearing gloves and limiting the working time.
Wherein all states of operation must be included
(e.g. times when the power tool is switched off
and times where the power tool is switched on
but running without load).
General Power Tool
Safety Warnings
WARNING!
► Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may
result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future
reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1. Work area safety
a) Keep work area clean and well lit. Cluttered
or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of fl am-
mable liquids, gases or dust.
Power tools create
sparks which may ignite the dust or fumes.
c)
Keep children and bystanders away while
operating a power tool.
Distractions can cause
you to lose control.
2. Electrical safety
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded)
power tools.
Unmodifi ed plugs and matching
outlets will reduce risk of electric shock.
b)
Avoid body contact with earthed or ground-
ed surfaces, such as pipes, radiators, ranges
and refrigerators.
There is an increased risk
of electric shock if your body is earthed or
grounded.
c) Do not expose power tools to rain or wet
conditions.
Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts.
Damaged or entangled cords
increase the risk of electric shock.
e) When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply.
Use of an RCD
reduces the risk of electric shock.
3. Personal safety
a) Stay alert, watch what you are doing and
use common sense when operating a power
tool. Do not use a power tool while you are
tired or under the infl uence of drugs, alcohol
or medication.
A moment of inattention while
operating power tools may result in serious
personal injury.
b) Use personal protective equipment. Always
wear eye protection.
Protective equipment
such as dust mask, non-skid safety shoes, hard
hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c)
Prevent unintentional starting. Ensure the switch
is in the off -position before connecting to power
source and/or battery pack, picking up or
carrying the tool.
Carrying power tools with your
fi nger on the switch or energising power tools that
have the switch on invites accidents.
IB_95883_PAS7.2A1_LB1.indb 11 IB_95883_PAS7.2A1_LB1.indb 11 26.02.14 08:38 26.02.14 08:38