7
GB/CY
Technical Data
PAS 3.6 A1 cordless screwdriver:
Rated voltage:
3.6 V
Rechargeable battery
(integrated): LITHIUM
Rechargeable battery
capacity: 1350
mAh
No-load speed:
n
0
200 min
-1
Torque: max.
4
Nm
Tool holder:
6.35 mm (
1
/
4
“)
PAS 3.6 A1-1 mains adapter:
INPUT:
Rated voltage:
230 - 240 V~ 50 / 60 Hz
Rated power:
5,5 W
OUTPUT:
Rated voltage:
6,2 V
Rated power:
400 mA
Charging time:
approx. 3 hrs.
Protection class:
II /
Noise and vibration data:
Measured values for noise are determined in accor-
dance with EN 60745. The A-weighted noise level
of the electrical power tool are typically:
Sound pressure level: 55 dB(A)
Sound power level: 80 dB(A)
Uncertainty K:
3 dB
Total vibration (vector sum of three directions) is
calculated in accordance with EN 60745:
Screwing:
Vibration emission value
a
h, D
= 2.101 m / s
2
,
uncertainty K = 1.5 m / s
2
WARNING!
The vibration level given in these
instructions has been measured in accordance with
a standardised measurement procedure specified
in EN 60745 and can be used to compare devices.
Different uses of the device give rise to different
vibration levels and in many cases they may exceed
the values given in these instructions. It is easy to
underestimate the vibration load if the electrical power
tool is used regularly in particular circumstances.
Note:
If you wish to make an accurate assessment
of the vibration loads experienced during a particular
period of working, you should also take into account
the intervening periods of time when the device is
switched off or is running but is not actually in use.
This can result in a much lower vibration load over
the whole of the period of working.
General safety advice for
electrical power tools
WARNING!
Read all the safety advice
and instructions!
Failure to observe the safety
advice and instructions may result in electric shock,
fire and / or serious injury.
Keep all the safety advice and instructions
in a safe place for future reference!
The term “electrical tool” used in the safety advice
refers to electrical tools powered by mains electrici-
ty (by means of a mains lead) and electrical tools
powered by rechargeable batteries (without a
mains lead).
1.
Workplace safety
a)
Keep your working area clean and
well lit.
Untidy or poorly lit working areas
can lead to accidents.
b)
Do not work with the device
in potentially explosive envi-
ronments in which there are
inflammable liquids, gases or dusts.
Electrical power tools create sparks, which can
ignite dusts or fumes.
c)
Keep children and other
people away while you are
operating the electrical tool.
Distractions can cause you to lose control of
the device.
Introduction / General safety advice for electrical power tools
Summary of Contents for PAS 3.6 A1
