Parkray Inset Chevin 20B Installation And Operating Instructions Manual Download Page 12

JINCHW09 Rev A 12/05/14 

Commissioning and Handover 

Upon  completion  of  the  installation,  allow  a 
suitable  period  of  time  for  any  fire  cement  and 
mortar to dry out.  A small fire may then be lit and 
checked to ensure the smoke and fumes are taken 
from the stove up the chimney and emitted safely 
to atmosphere.  Do not run the stove at full output 
for at least 24 hours. 
 
On 

completion 

of 

the 

installation 

and 

commissioning,  ensure  that  the  operating 
instructions  and  operating  tools  for  the  stove  are 
left  with  the  customer.    Advise  the  customer  on 
the  correct  use  of  the  appliance  with  the  fuels 
likely  to  be  used  on  the  stove  and  warn  them  to 
use only the recommended fuels for the stove. 
 
Advise  the  user  on  what  to  do  should  smoke  or 
fumes be emitted from the stove.   
 
The user should be warned to use a fireguard to BS 
6539  in  the  presence  of  children,  aged  and/or 
infirm persons. 
 

Operating Instructions 

Read the ‘General Guidance’ Section at the start 
of these instructions before operating your stove 
for the first time. 
 
Allow sufficient clearance between the stove and 
pictures, plasma screen televisions or ornaments 
etc,  as  these  could  be  damaged  and  could 
potentially  create  a  fire  hazard  (For  more 
information read the ‘Material Clearance’ section 
of these installation instructions). 
 
WARNING  –  This  appliance  will  be  hot  when  in 
operation  and  due  care  should  be  taken.  The 
supplied operating tool or gloves may be used to 
open the door and operate the air controls. 
 

A

EROSOLS

 

Do not use an aerosol spray on or near the stove 
when it is alight. 
 

A

IR 

C

ONTROLS

 

Installed and used correctly this stove will burn 
cleanly and efficiently. Therefore, to avoid the 
disappointment of poor performance, please 
familiarize yourself with the controls and their 
recommended settings before use.

 

T

HERMOSTAT

 

The thermostat is controlled by the knob on the 
side of the stove with settings from 0 - 10. The 
thermostat generally operates between 50° to 90°. 
Experiment with the settings to find the desired 
temperature. 
 

 

S

ECONDARY 

A

IR

 

Secondary air is controlled via the slider above the 
door(s), it is this “Airwash” that keeps a clean and 
uninterrupted view of the fire. 
  

 

 

L

OCOMOTIVE 

G

RATE

 

Your Parkray Ltd Stove is fitted with a locomotive 
type grate. So that de-ashing can be carried out 
cleanly and easily, it is riddled from the outside of 
the stove with the doors closed. 
 

 

 

SHUT 

OPEN 

Summary of Contents for Inset Chevin 20B



















Reviews: