background image

 15

Output signals

6     Installation

Instruction book, IQAN- LC6-X05

Connecting of -H1 handle outputs

When you connect the IQAN-LC6-X05 joystick handle functions to a module or 
standalone controller you may have proportional outputs from rocker and knob. You 
should use both primary and secondary signals from the rocker or knob. The primary 
signal for the axis is connected to a VIN, 

voltage input

 and the secondary signal for the 

axis, if used, is connected to a separate VIN on the controller module. 

Connect each primary output 10%-90% Vs output signal to VIN, and optionally 
connect the corresponding secondary output 90%-10% Vs output signal to another 
VIN. 

W

ARNING

The previous example is presented with limited information to explain the use of 
primary and secondary signals from the -H1 handle rocker and knob. Safety 
considerations such as the use of an ’operator present’ switch to enable outputs etc. are 
always recommended.

LC6-H1 handle loss of ground

When using only one of the two possible axis on the -H1 handle, either rocker or knob, 
the primary signal from the axis not in use must be pulled to ground through a 10k-50 k 
ohm resistor for safety reasons. If this is not done the connected output will have a 
unintentional activation if the ground connection to the handle is lost

Connect the primary output pin from the unused axis, through a resistor, to ground. 

W

ARNING

Possible unintentional activation of the connected axis if the ground connection is lost!

If the supply ground is disconnected from the handle sensors, the output from the 
connected axis will be around 3.6 V if unused output is not grounded.

EXAMPLE

Connecting -H1 rocker and knob outputs to a module.

EXAMPLE

Grounding one of the signals from an unused axis.

to valve section controlled

to valve section controlled

VOUT-Z1B

VOUT-Z2B

VOUT-Z1A

VOUT-Z2A

by knob of joystick

by rocker of joystick

IQAN module

H1 handle

VIN

VIN

VIN
VIN

to valve section controlled

VOUT-Z1B

VOUT-Z2B

VOUT-Z1A

VOUT-Z2A

by rocker of joystick

IQAN module

H1 handle

VIN

VIN

10K
to
50K

Summary of Contents for IQAN-LC6-X05
























Reviews: