background image

Electromechanical Automation

Product Management & Application

11.02.2008

Klaus Zimmer
Parker Hannifin GmbH & Co KG
EME  - Electromechanical Automation Europe
Postfach 17 20 * 77607 Offenburg
Robert-Bosch-Straße 22 * 77656 Offenburg
E-Mail: 

[email protected]

C3 I20 T11 ControlManager application note eng.doc

Seite 2 von 20

Version: 16

________________________________________________
Copyright © 2008 Parker Hannifin GmbH & Co. KG EME
All Rights reserved.
Windows NT®, Windows 2000™, Windows XP™ are trademarks of Microsoft
Corporation.

EME - Electromechanical Automation Europe

Germany

:

Parker Hannifin GmbH & Co. KG
Electromechanical Automation
Postfach: 77607-1720
Robert-Bosch-Str. 22
D-77656 Offenburg
Tel.: +49 (0)781 509-0
Fax: +49 (0)781 509-98176
E-mail: [email protected] mailto:[email protected]
Internet: www.parker-eme.com http://www.parker-eme.com

England

:

Parker Hannifin plc
Electromechanical Automation
Arena Business Centre
Holy Rood Close
Poole, Dorset BH17 7BA UK
Tel.: +44 (0)1202 606300
Fax: +44 (0)1202 606301
E-mail: [email protected] mailto:[email protected]
Internet: www.parker-eme.com http://www.parker-eme.com

Italy

:

Parker Hannifin S. p. A
Electromechanical Automation
Via Gounod 1
I-20092 Cinisello Balsamo (MI), Italy
Tel.: +39 (0)2660 12459
Fax: +39 (0)2660 12808
E-mail: [email protected] mailto:[email protected]
Internet: www.parker-eme.com http://www.parker-eme.com

EMN - Electromechanical Automation North America

USA

:

Parker Hannifin Corporation
Electromechanical Automation
5500 Business Park Drive
Rohnert Park, CA 94928
Phone #: (800) 358-9068
FAX #: (707) 584-3715
E-mail: [email protected] mailto: [email protected]
Internet: www.compumotor.com http://www.compumotor.com

Summary of Contents for Compax3H050V4





















Reviews: