manualshive.com logo in svg

Parker 6053-LINK-00 TechBox, Product Manual

Share
Download
Parker 6053-LINK-00 TechBox Product Manual Download Page 14

9

 

LINK TechBox/TechCard Instruction Manual - HA470016 Issue 5  

 

 

 

FAULT  

 

Range: Enumerated - see below

The fault state of the Technology Option card. 

Enumerated Value : Fault State

 

0 : NONE:

 Normal operating mode.

 

1 : PARAMETER:

 Confirm that tag exists in the 

LINK

 Configuration.

 

2 : TYPE MISMATCH:

 Confirm that type of tag is valid.

 

3 : SELF TEST:

 The self test has failed. Replace TechCard/TechBox.

 

4 : HARDWARE:

 Hardware error. Replace TechCard/TechBox.

 

5 : MISSING:

 TechCard/TechBox not installed/

 

 

VERSION 

 

Range: 0000 to FFFF  

The version of the Technology Option. If no option is fitted then the version is set to zero. 

 

INPUTS  (1–5) 

 

 

Range: 0000 to FFFF  

Not used with the 

LINK

 Technology Option 

 

OUTPUTS  (1–2) 

 

 

Range: 0 to 9999  

Not used with the 

LINK

 Technology Option 

Other Function blocks 

While configuring the “TEC OPTION”, you may also insert other Link function blocks into the 
TechBox template.  This can be done by using ConfigEd or DSD. 

DSD and ConfigEd 

When configuring the “TEC OPTION” function block using DSD the TechBox and drive can be 
programmed completely using the DSD software.  Drive System Designer (DSD) provides the 
TechBox templates for the 590+ and 690+ only.  When using ConfigEd to program the TechBox 
Tag Readers and Tag Writers are used. 

Install 

If using the MMI, remember to save the set-up via the Save Parameters or Save Config menu. 
If using ConfigEd Lite install the configuration into the drive through the P3 port (RS232 
configuration port), using the 

Command/Install

 pulldown menu. For more details on installing a 

configuration, refer to the ConfigEd Lite Instruction Manual (RG352747) Chapter 4 page 4-7. 
If using ConfigEd or DSD, install the configuration using socket J2 on the Link TechBox (RS232 
configuration port) 

Command/Install

 pulldown menu. For more details on installing a 

configuration, refer to the ConfigEd Instruction Manual (RG353792) Chapter 4 page 4-26. 

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for 6053-LINK-00 TechBox















































Reviews:

No comments

Brands by name

Popular brands

Load more brands