background image

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

AVIS

RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

CAUTION!

 

The amplifier runs on 230 VAC voltage. Removing the cover will expose 

you to a potentially dangerous voltage! Do not use the unit if the electrical power cord is 
frayed or broken.

Power is supplied from 230 VAC single-phase grounded 50 / 60 Hz source!

CAUTION!

 The amplifier can yield 

dangerous

 output voltage! Do not  touch the non-

insulated cable parts, connected to the unit in operation!

CAUTION!

 

The  high  sound  pressure  level  of  speaker  systems  generated  by  high 

output power, delivered by the amplifier, may be hazardous to your hearing. Please, 
take adequate  safety precautions. 

WARNING!

 

The amplifier yields high output power. The manufacturer shall not be held 

responsible for any damage to the speakers caused by excessive power from the unit. 

WARNING SIGNS:

Important information!

 

Intended  to  warn  the  user  about  any  important  applicable  information 

contained in this Owner’s Manual.

Hazardous voltage inside!

 

Intended to warn the user about electric shock hazard due to high voltage 
inside the product. 

Summary of Contents for TA Series
























Reviews: