Paradyne TNE1500-P Installation Instructions Manual Download Page 3

3

7. The rights granted under this Agreement may not be assigned, sublicensed or 

otherwise transferred by the Licensee to any third party without the prior written 
consent of Paradyne.

8. This Agreement and the license granted under this Agreement shall be terminated 

in the event of breach by the Licensee of any provisions of this Agreement. 

9. Upon such termination, the Licensee shall refrain from any further use of the 

Software and destroy the original and all copies of the Software in the possession of 
Licensee together with all documentation and related materials.

10. This Agreement shall be governed by the laws of the State of Florida, without 

regard to its provisions concerning conflicts of laws.

Product Documentation

This document describes units manufactured after 14 March 2005. See the prior version 
of this document for information about units manufactured on or before that date.

Complete documentation for Paradyne products is available at 

www.paradyne.com

Select 

Support 

 Technical Manuals

.

To order a paper copy of a Paradyne document, or to speak with a sales representative, 
please call 1-727-530-2000. 

Warranty, Sales, Service, and Training Information

Contact your local sales representative, service representative, or distributor directly for 
any help needed. For additional information concerning warranty, sales, service, repair, 
installation, documentation, training, distributor locations, or Paradyne worldwide office 
locations, use one of the following methods:

„

Internet:

 Visit the Paradyne World Wide Web site at 

www.paradyne.com

. (Be sure 

to register your warranty at 

www.paradyne.com/warranty

.)

„

Telephone:

 Call our automated system to receive current information by fax or to 

speak with a company representative.

Within the U.S.A., call 1-800-795-8004

Outside the U.S.A., call 1-727-530-2340

Package Contents

Unpack and Inspect the Equipment. The following components should be included:

„

1  TNE1500

„

1  Power supply

If there is any visible damage, do not attempt to connect the device. Contact your sales 
or service provider.

Summary of Contents for TNE1500-P

















Reviews: