Paradyne TNE1500-P Installation Instructions Manual Download Page 13

13

A plug and jack used to connect this equipment to the premises wiring and telephone 
network must comply with the applicable FCC Part 68 rules and requirements adopted 
by the ACTA. See installation instructions for details.

If the network extender causes harm to the telephone network, the telephone company 
will notify you in advance that temporary discontinuance of service may be required. But 
if advance notice is not practical, the telephone company will notify the customer as 
soon as possible. Also, you will be advised of your right to file a complaint with the FCC 
if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations or 
procedures that could affect the operation of the equipment. If this happens the 
telephone company will provide advance notice in order for you to make necessary 
modifications to maintain uninterrupted service.

If trouble is experienced with this equipment, please contact your local sales 
representative, service representative, or distributor directly for any help needed. For 
additional information concerning warranty, sales, service, repair, installation, 
documentation, training, distributor locations, or Paradyne worldwide office locations, 
use one of the following methods:

„

Internet: Visit the Paradyne World Wide Web site at www.paradyne.com. (Be sure 
to register your warranty at www.paradyne.com/warranty.)

„

Telephone: Call our automated system to receive current information by fax or to 
speak with a company representative.

Within the U.S.A., call 1-800-795-8004

Outside the U.S.A., call 1-727-530-2340

If the equipment is causing harm to the telephone network, the telephone company may 
request that you disconnect the equipment until the problem is resolved.

The customer may make no repairs to the equipment.

Connection to party line service is subject to state tariffs. Contact the state public utility 
commission, public service commission or corporation commission for information.

Summary of Contents for TNE1500-P

















Reviews: