Paradyne TNE1500-P Installation Instructions Manual Download Page 1

1

TNE1500-P and TNE1500-S

T1 Network Extenders Installation Instructions

Document Number TNE1-A2-GN10-10

September 2005

Contents

Software and Firmware License Agreement

.................................................

1

Product Documentation

................................................................................

3

Warranty, Sales, Service, and Training Information

......................................

3

Package Contents

.........................................................................................

3

Connecting to Power

.....................................................................................

4

Configuring the T1 Port

.................................................................................

5

Connect the T1 Line

.....................................................................................

8

Connect the Ethernet Line

............................................................................

9

LED Indicators

.............................................................................................. 10

EMI Notices

.................................................................................................. 12

ACTA Customer Information

......................................................................... 12

Supplier's Declaration of Conformity

............................................................. 14

Notice to Users of the Canadian Telephone Network

................................... 14

Important Safety Instructions

........................................................................ 15

Software and Firmware License Agreement

ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS
TERMS, YOU MAY USE THE SOFTWARE AND/OR FIRMWARE INCORPORATED
INTO THE PARADYNE PRODUCT. BY USING THE PARADYNE PRODUCT YOU
SHOW YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT.

IN THE EVENT THAT YOU DO NOT AGREE WITH ANY OF THE TERMS OF THIS
LICENSE AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT IN ITS
ORIGINAL PACKAGING AND YOUR SALES RECEIPT OR INVOICE TO THE
LOCATION WHERE YOU OBTAINED THE PARADYNE PRODUCT OR THE
LOCATION FROM WHICH IT WAS SHIPPED TO YOU, AS APPLICABLE, AND YOU
WILL RECEIVE A REFUND OR CREDIT FOR THE PARADYNE PRODUCT
PURCHASED BY YOU.

Summary of Contents for TNE1500-P

















Reviews: