Paradyne FrameSaver NP 64+ User Manual Download Page 142

Page: 142 / 143

Appendix

980-001-0221C

FrameSaver NP 64+ User’s Manual - Installation Guide

A-7

March 2001

Modem Status,
Fault

Modem Status shows the highest priority internal modem related fault currently detect-
ed. This is displayed on the System View screen.

Table A-7 Modem Status, Fault

Display

Description

ISDN Adapt Fault

The ISDN hardware has failed.

ISDN Line Failure

The ISDN line of at least one B-Channel is faulty.

ISDN SPID Failure

An invalid or incorrect SPID has been entered for at least one B-Channel.

Modem Failure

Failure of Modem hardware detected by the unit.

Dial Line Failure

Failure of routine Dial Line test detected.

Bch In Use by Bkp

B-Channel is in use for Backup operation.

Bch In Use by Dmd

B-Channel is in use for On-Demand operation.

Summary of Contents for FrameSaver NP 64+
















































































































































Search results

Summary of Contents for FrameSaver NP 64+

Reviews:

Related manuals for FrameSaver NP 64+

Brands by name

Popular brands

Paradyne FrameSaver NP 64+, User Manual

Search results

Summary of Contents for FrameSaver NP 64+

Reviews:

Related manuals for FrameSaver NP 64+

Brands by name

Popular brands