background image

 9

7984-A2-GZ40-00

February 1999

Table 3.

System Options

DSL Mode

Possible Settings: LTUNTU
Default Setting: NTU

Controls whether the unit is configured as a control unit or tributary unit.

NOTE:

Changing this option will reset the card.

Test Timeout

Possible Settings: Enable, Disable
Default Setting: Enable

Allows tests to end automatically. The feature should be enabled when the unit is
remotely managed, so that control can be regained after a test is accidentally executed.

Test Duration (min)

Possible Settings: 1–120
Default Setting: 10

Number of minutes for a test to be active before automatically ending.

Telco Initiated Loopback

Possible Settings: Enable, Disable
Default Setting: Enable

Determines if the unit will respond to Telco loopback commands on the DSX-1 interface.

Remote Telco Loopback

Possible Settings: Enable, Disable
Default Setting: Disable

Determines if the unit will perform a Telco initiated loopback on just the local unit or if the
loopback will be performed on the remote DSL unit.

Table 4.

Communication Port (1 of 2)

Port Use

Possible Settings: TerminalNet Link
Default Setting: Terminal

Specifies how the communications port is to be used.

Port Type

Possible Settings: AsynchronousSynchronous
Default Setting: Asynchronous

When Port Use is set to Net Link, Port Type controls whether the communication port
will be asynchronous or synchronous.

Data Rate

Possible Settings: 9.614.4, 19.2, 28.8, 38.4
Default Setting: 9.6

Specifies the communication port baud rate.

Summary of Contents for 7984























Reviews: