background image

10   Complete Installation Manual   

6.7

PANIC ALARMS

The panic alarm, if programmed, will immediately generate an alarm after pressing and holding the 

[1]

 and 

[3]

 keys for two seconds (see section

4.4) (disabled by default).

6.8

ALARM MEMORY DISPLAY

A record of the zones that were in alarm the last time the system was armed will be stored in memory. After disarming the system, press the

[

MEM

]

 button to display the zones that were in alarm. To exit the 

Alarm Memory Display

, press the 

[

CLEAR

button. The control panel will erase the

contents of the alarm memory every time the system is armed. 

Zone 

[5]

 will illuminate if an alarm has occurred on the keypad zone or if the keypad’s on-board tamper was triggered (see section 2.10).

The control panel cannot distinguish the difference between the two. Zone 

[8]

 will illuminate if the panic alarm keys (see section 4.4)

were pressed. 

6.9

PROGRAMMING CHIME ZONES

Press and hold any key from 

[1] 

to 

[5]

 for 3 seconds to activate or deactivate 

Chiming

 for zones 1 to 6. For example, press and hold the

 [1]

 key

to enable chiming on zone 1. If after pressing and holding a key, the keypad emits a confirmation beep, the chime feature has been enabled for that
zone. If the keypad emits a rejection beep, the chime feature has been disabled for the corresponding zone.

6.10

KEYPAD MUTING

Press and hold the 

[

CLEAR

]

 button for 3 seconds to enable or disable keypad muting. When muted, the keypad will only beep when a key is

pressed and when the keypad emits a rejection or confirmation beep. All other beep functions are disabled. 

7: 

PROGRAMMING GUIDE

To program the 

Spectra 1727

 control panel, use a keypad to enter the 

Programming Mode

 as shown below.

USER CODES

Sections 

[02] 

to

 [09]

 can only be programmed by the System Master Code (see section 5.4).

Table 4: Pre-programmed Options for User Codes

Section

User Codes

Can

Change Code

Can 

Reg. Arm

Can 

Disarm

Can

Bypass Arm

Can

Stay Arm

Can

Force Arm

[01]

Installer Code

[02]

Master Code

[03]

User Code 01

[04]

User Code 02

[05]

User Code 03

[06]

User Code 04

[07]

User Code 05

[08]

User Code 06

[09]

User Code 07

DEFAULT INSTALLER CODE: 0000/000000 

DEFAULT SYSTEM MASTER CODE: 1234/123400

How Do I Enter Programming Mode?

STEP 1:

 

Press

 [

ENTER

]

STEP 2:

 

Enter your

 [

INSTALLER

 

CODE

(default: 0000/000000) or 

[

SYSTEM

 

MASTER

 

CODE

]

 

(default: 1234/123400)

STEP 3:

 

Enter the 2-digit 

[

SECTION

you wish to program

STEP 4: Enter the required

 [

DATA

]

Section #

[01]

Installer Code

[

ENTER

[

CURRENT

 

INSTALLER

 

CODE

[01] 

new 4- or 6-digit Installer Code

Summary of Contents for SPECTRA 1686H





















Reviews: