manualshive.com logo in svg

Paradox Digiplex Liberator DGP-319, Installer'S Manual

Share
Download
Paradox Digiplex Liberator DGP-319 Installer'S Manual Download Page 2

1.0 TABLE OF CONTENTS

INTRODUCTION  ........................................................................... 5

1.1  Technical Specifications ...................................................................... 5
1.2  System Features ................................................................................. 5

INSTALLATION  ............................................................................ 6

2.1  Location ............................................................................................... 6
2.2  Connections and Mounting  ................................................................. 6

PROGRAMMING ........................................................................... 8

3.1  Entering Module Programming Mode  ................................................. 8

3.1.1 Feature Select Programming ........................................................... 9

3.2  Low Battery Supervision  ..................................................................... 9
3.3  Check-in Supervision  ......................................................................... 10
3.4  Tamper Supervision on Receiver Module .......................................... 10
3.5  PGM Deactivation Mode  .................................................................... 11
3.6  PGM Base Time ................................................................................. 11
3.7  PGM Timers ....................................................................................... 12
3.8  PGM Activation Event  ........................................................................ 12
3.9  PGM Deactivation Event .................................................................... 13
3.10 PGM Override  ................................................................................... 14
3.11 System Reset .................................................................................... 14
3.12 Viewing Unknown Serial Numbers .................................................... 15

DETECTORS AND CONTACT SWITCHES  ................................ 16

4.1  Assigning Detectors & Contact Switches to Receiver ........................ 16
4.2  Assigning Detectors & Contact Switches to Zones  ............................ 18
4.3  Viewing Signal Strength of Detectors & Contact Switches  ................ 18

I319EI01.fm  Page 3  Wednesday, September 29, 1999  10:56 AM

Summary of Contents for Digiplex Liberator DGP-319






































Reviews:

No comments

Brands by name

Popular brands

Load more brands