background image

 

 

Page  

5.2  Dialling  

( select signalling to be dialed by PULSE/TONE switch, often set to TONE)

 

 

Move the TALK/RING/MONITOR switch to the MONITOR position then 

connect the lead clips  to the telephone line. Listen to receiver (ear piece) to 
verify that the line is idle ( silent)  

 

Move the TALK/RING/MONITOR switch to the RING position and if AC 

present on the lines, ringer will alarm with continuous ringing, user should 
disconnect lead clips from the line immediately and carefully.

 

Avoid touching 

any metal parts and short test clips to each other. 
 
 
 

 

 

Move the TALK/RING/MONITOR switch to TALK position and verify if 

dial tone is received. Key the calling number to the keypad. If tone signalling 
being selected. The responsible frequency tones of each digit will be 
generated for each button pressing.  

 

End the dialling by moving back the TALK/RING/MONITOR switch to 

the MONITOR position (recommended when stanby or store the test set). 

 

Press FLASH button to on and off-hook if need to dial again. 

 

Note:

 Operating on xDSL and data lines will not disrupt service on network 

during and after dialing 
 

5.3    Polarity Check. Move the TALK/RING/MONITOR switch to MONITOR then 

connect the lead clips to the line under testing. Move the same switch from 
MONITOR to TALK with instruction described in 5.2 above. The red LED will not 
light if the red lead clip is connected to the ring (negative) side of the line and the 
black lead clip is connected to the tip (positive) side of the line. The red LED will 
light if the lead clips are reversed that is, with the red lead clip connected to the tip 
(positive) side and the black lead clip connected to the ring (negative) side. 

 
 

5.4  Programing and Making a Speed dialing.  ( repertory memory) 

Program number,  connect handset to the lines then off-hook by slide bottom 

switch to TALK  then  1) press PROG   2) press MEM  3) press digit 

0 - 9

 for 

memory location  4) enter telephone number which can include *  # or 

FLASH

  

5)  press PROG  

          Speed dialing, off-hook then 1) press MEM   2) press digit 

0 - 9

 for memory 

           location   

 
 
 
 
 
 
 
 
 
 
 

Figure 2 

PULSE/TONE SWITCH 

TALK/RING/MONITOR 
SWITCH 

Last Number Redial 

 

TONE  
PULSE  

 

TALK 

RING 

MONI - 

TOR 

 

 

 

Summary of Contents for LTS-48







Reviews: