background image

 

 Rotarod 

 

19 

8.4.

 

CONDUCTING EXPERIMENTS 

1)

 

Turn on the instrument using the POWER switch. 

2)

 

Lower the LEVERS, this will prevent the timer counters from beginning. 

3)

 

Select the desired working mode. 

a)

 

CONSTANT 

1)

 

Establish the desired initial rod speed using the “+”, “-”or “Speed” buttons. The 
rod will not begin rotating until the “Start” button is pressed. 

 

 

 

 

Figure 14. Set rod speed screen

 

 

2)

 

Press the “Start” button and this will initiate the rod rotation at the set speed 
in step 1.  
 

3)

 

If  any  LEVER  remains  in  the  raised  position,  the  message  “Place  all  levers 
down”  will  be  shown  on  the  display  until  all  the  LEVERS  are  in  depressed 
position. 

 

4)

 

Place the animals in their respective lanes on the rod, as shown in Section 8.3. 

 

5)

 

Manually  lift  the  LEVERS  to  activate  the  relevant  counters  for  the  lanes  that 
will be used in that trial. 

 

6)

 

Use the “+”, “-”or “Speed” buttons to modify the desired rod speed. 

 

Accept, cancel changes buttons 

Edit the speed in this box by pressing the numbers on the keypad 

Keypad 

Summary of Contents for 76-0770
































Reviews: