Panduit ATLONA AT-UHD-CLSO-601 User Manual Download Page 26

Page: 26 / 35

atlona.com

Toll free: 1-877-536-3976

Local: 1-408-962-0515

Commands

The command codes are case sensitive, do not change capitalization, spacing, or lettering.

Command

Feedback

Description

PWON

Power ON

PWOFF

Stand-by

PWSTA

PWON/PWOFF

Get system power status

RS232zoneX[Y]

RS232zoneX[Y], X: 1-8. [Y] is the command string sent to the display
device or source through the RS-232 port

RS232paraX[Y]

RS232paraX[baudrate,databit,parity,stopbit] X is 1-8. [Y] is the
parameter for RS-232

CSpara[Y]

Set RS232 parameter
[Y] is the parameter for RS-232.

VOL+

VOL(xx)

Turns the volume up one level

VOL-

VOL(xx)

Turns the volume down one level

VOL(xx)

e.g.

VOL(10)

Turns volume to the specified level <xx: 10 ~ -80>
Read the volume current level status => VOL

e.g.

Adjusts the master volume level to -23dB => VOL(-23)

MVOL+

MVOL(xx)

Turns the MIC volume up one level

MVOL-

MVOL(xx)

Turns the MIC volume down one level

MVOL(xx)

e.g.

MVOL(30)

Turns MIC5V volume to the specified level <xx: 30 ~ -80>
Read the MIC5V volume current level status => MVOL

MICx [Y]

e.g.

MICatime 20

Sets up MIC values
x = on / off / sta / atime (attack time) / rtime (background release
time) / sens (microphone sensitivity level) / reduce (background
reduce level) Y = value (ex. 20)

LVOL+

LVOL(xx)

Turns the Line volume up one level

LVOL-

LVOL(xx)

Turns the Line volume down one level

LVOL(xx)

e.g.

LVOL(0)

Turns Line volume to the specified level <xx: 0 ~ -80>
Read the Line volume current level status => LVOL

SnVOL+

SnVOL(xx)

Turns the Sub volume up one level <n: 1-6> (n = input number)

e.g.

Adjusts the HDMI 4 volume to up => S4VOL+

SnVOL-

SnVOL(xx)

Turns the Sub volume down one level <n: 1-6> (n = input number)

e.g.

Adjusts the VGA1 volume to down => S5VOL-

SnVOL(xx)

e.g.

S2VOL(-15)

Turns Sub volume to the specified level <n: 1-6, xx: 0 ~ -80>
Read the Sub volume current level status => SnVOL

e.g.

Adjusts the HDMI1 volume level to -10dB => S1VOL(-10)

VOLMute [Y]

VOLMute [on/off/sta]. Set volume to mute on. => VOLMute on

Menu[X]

e.g.

MenuDown

Control OSD interface, [X]: Sw/Up/Down/Left/Right/Info/Sel

e.g.

Select OSD option => MenuSel

Lock

Locks the front panel

Unlock

Unlocks the front panel

Version [Y]

e.g.

Version osd

Version [Y]

e.g.

Version x.x.xx

Brings up the software versions: ex. Version mcu
firmware [mcu]
OSD menu [osd]
DSP [dsp]
FPGA [fpga]

Type

AT-UHD-CLSO-601 Brings up the model information

Mreset

Reset device to manufacture default

Summary of Contents for ATLONA AT-UHD-CLSO-601




































Search results

Summary of Contents for ATLONA AT-UHD-CLSO-601

Reviews:

Related manuals for ATLONA AT-UHD-CLSO-601

Brands by name

Popular brands

Panduit ATLONA AT-UHD-CLSO-601, User Manual

Search results

Summary of Contents for ATLONA AT-UHD-CLSO-601

Reviews:

Related manuals for ATLONA AT-UHD-CLSO-601

Brands by name

Popular brands