31
30
U S E R M A N U A L
P A N D O R A D X L 1 9 2 0 L / 1 9 3 0 L C A R S E R V I C E - S E C U R I T Y S Y S T E M
that the system will return to the programming menu. If the PIN-code is not entered within 10 seconds
or the input is incorrect, a siren will sound one signal,
LED
will produce the series of red and green
flashes and the system will return to the programming menu.
Enabling radio tag:
LED
indicator will light red after entering the programming level. The system will wait for action.
Press
VALET
button once to enable radio tag. The system will confirm enabling with one short sound
signal of a siren and a green
LED
light. After that the system will return to the programming menu.
Level 16 – Updating built-in Bluetooth modem firmware
Download the firmware from www.pandorainfo.com and install Pandora BT or Pandect BT
application on your mobile device (Android version 4.4 or higher with Bluetooth 4.0 Low Energy
or higher support).
To update firmware of the built-in Bluetooth modem, enter programming mode and press
VALET
button 16 times. Find your system in the mobile application, go to detected devices and upload the
previously downloaded firmware to the system.
Level 17 – Programming bypass of original immobilizer
Bypass learning procedure is performed on this level. A detailed manual can be found in
installation scheme for a car in AlarmStudio.
Enter programming mode and press
VALET
button 17 times.
LED
indicator will be lit green. If
system installation was performed correctly on successful engine start using a key,
LED
indicator will
flash green. After completing of the procedure, a siren will emit a short sound signal and
LED
indicator
will light green. If the learning procedure finishes with an error,
LED
indicator will light red.
Saving changes:
To finish the learning procedure, switch off the ignition and press
VALET
button. The system will
return to programming mode.
Level 18 – Registering and unregistering mobile device
The system supports only one mobile device. Registration of a new mobile device (if the
system has previously registered device) is not allowed without deleting procedure. When you
overwrite the same device in the system memory, you should delete the Bluetooth connection
on your mobile device, delete the mobile device from the system memory and then register the
mobile device in the system memory.
To register a mobile device, enter the programming mode and press
VALET
button 18 times.
LED
indicator will light green (green light indicates the system is ready to register a mobile device)
and the system will enter the mobile device registration mode. Red light of
LED
indicates the
system has already had registered mobile device, overwriting of mobile device can be done only
after deleting procedure.
Mobile device registration:
LED
indicator will light green after entering the level. Open ”Pandora Online” mobile application,
go to ”Bluetooth Control” –> ”Not specified” menu and select your device. The application will
search for the system via Bluetooth connection. Select the found system, the system and the
mobile device will be automatically paired. The system will confirm the pairing with a sound signal
of a siren and red light of LED indicator.
Deleting mobile device:
LED
indicator will light red after entering the level. Press
VALET
button and hold it for more than 4
seconds, release the button. The system will confirm deleting with the series of sound signals of a siren
and the system will return to mobile device registration mode (
LED
indicator will light green).
Saving changes:
To finish the registration of a mobile device,
VALET
button should be pressed once, the series of
red and green flashes of the status
LED
indicator will confirm the saving, switch on the ignition to
automatically save the settings and exit the programming mode.
Levels 19, 20 – Updating radio relays №1, №2 firmware
Download the firmware from www.pandorainfo.com and install Pandora BT or Pandect BT
application on your mobile device (Android version 4.4 or higher with Bluetooth 4.0 Low Energy
or higher support).
To update firmware of radio relays №1, №2, enter the programming mode and press
VALET
button
19 times for radio relay №1 and 20 times for radio relay №2. Find your system in the mobile application,
go to detected devices and upload the previously downloaded firmware to the system.
2
5
1
4
3
NO
NC
COM
programming
6
Antenna 2,4 Ghz
+12V
