background image

41

40

USER MANUAL

PANDORA DXL 1100L SERVICE-SECURITY

S Y S T E M   C O N F I G U R A T I O N   A N D   P R O G R A M M I N G

PREPARATION FOR SYSTEM PROGRAMMING FROM A COMPUTER

The system allows programming all settings and updating software of the base unit 

via micro-USB cable. If the base unit has not yet been installed in the vehicle, it will be 

powered via micro-USB cable while programming. To program using a computer, you 

need a standard USB cable, a computer with Windows XP/ Vista/7/8/10 and Pandora 

AlarmStudio application (you can download it from 

pandorainfo.com

). 

In preparation to the programming these stages should be followed:

•  connect the system and PC via USB cable;

•  start Pandora AlarmStudio;

•  enter the programming settings mode by entering the service PIN-code.

 

UPDATING FIRMWARE

It is recommended to update firmware of the base unit before installing and 

programming the system (actual version of the firmware you can download from 

pandorainfo.com

). You can update firmware using AlarmStudio application after 

entering programming mode or using quick boot algorithm (PIN-code is not 

required). If the boot mode has been interrupted for some reason and the status 

indicator lights red, you need to load firmware using quick boot mode (without 

entering PIN-code).

«Quick boot» mode:

Open AlarmStudio, de-energize and disconnect the system; press and hold 

VALET 

button; release the button immediately after connecting the system and a computer 

via USB cable; the system will enter boot mode. You can use quick boot mode for 

updating firmware when the system is in any security state (armed or disarmed).

 

S Y S T E M   C O N F I G U R A T I O N   A N D   P R O G R A M M I N G

PROGRAMMING USING VALET BUTTON

The system allows programming some settings using 

VALET

 button. To configure all 

the settings use a computer to program the system.

Enter programming mode by entering «Service PIN-code», Use 

VALET

 button to 

enter the desired level number (press the button a number of times, equal to level 

number; pauses between presses should not exceed 1 second). The system will 

confirm correct input with red and green 

LED

 flashes and proceed to the desired 

level. If the input was incorrect, the system will not confirm input and will await a new 

level input after a series of green and red flashes.

Level 1

Recording remote controls into the system memory

Level 2

Changing the factory preset service PIN-code

Level 3

Recording the idle speed to the system memory

Level 4

Resetting to factory settings

Level 1 – Recordings remotes into the system memory

Prepare to register all remote controls (you can register up to 4 remote 

controls), install batteries in the remote controls and turn on the main remote 

control if it was turned off. 

Enter programming menu and then press 

VALET

 button 

once.

 LED

 indicator will light green and the system will enter the remote control 

recording mode. Remote controls are recorded one by one, in any order and without 

time limit. All previously recorded remote controls will be removed when you record 

new remote controls or overwrite old remote controls.

Recording remote control:

Press three buttons simultaneously (on the remote control) and hold them for 1 

second (until a short beep from the main remote control), then release the buttons. 

Summary of Contents for DXL 1100L


























Reviews: