15
14
USER MANUAL
PANDORA DXL 0110L CAR SERVICE-SECURITY SYSTEM
WIRING DESCRIPTION
• Wire «1» (White) (DATA TX)
— It connects to appropriate additional
devices wires (optional).
• Wire «2» (Red-black) (LED/VALET)
— It should be connected to the red
wire of VALET button. Black wire of VALET button connects to the grounding spot.
• Wire «3» (Orange-white) («CAN1-High»)
— It connects to appropriate
CAN-High wire of the car.
• Wire «4» (Yellow-white) («CAN2-High»/CH2)
— Factory setting is
«Open central lock». A negative impulse of 0,8 seconds is formed on the wire
to open central lock. Logic of the channel’s operation can be set in the table
of system outputs. When the car model code with support for CAN2-bus is
selected, channel CH2 stops to operate as an output.
• Wire «5» (Gray) (СН1/INP1)
— Factory setting is «Beeper OUT». The wire
connects to the corresponding «-» wire of the Beeper sound emitter. Sound
signals from the Beeper location should be heard from the driver’s seat. «+»
out should be connected to reliable conductor with constant voltage of 12V.
LED indicator can be connected in parallel to Beeper through a 1000…1500
Ohm resistor. Negative output of additional channel, maximum load current
is 200 mA. This output is multipurpose, it can operate as an input or output in
accordance with selected logic.
• Wire «6» (Green) (СН4/INP4)
— Factory setting is «Control turn
indicators». This wire connects to the hazard flashers button. Negative
output of additional channel, maximum load current is 200 mA. This output is
multipurpose, it can operate as an input or output in accordance with selected
logic.
• Wire «7» (White-blue) (INP5)
— Factory setting is «Brake pedal limit
switch». This wire connects to the brake pedal button where 12V voltage
appears when the pedal is pressed (stop lights wire). Brake pedal signal is one
of the system’s security zones. This input is multipurpose, it can operate in
accordance with selected logic.
• Wire «8» (Black) («Ground»)
— It should be connected to the car body
in a grounding spot. This wire should be connected first during installation.
• Wire «9» (Blue) (DATA RX)
— It connects to appropriate additional
devices wires (optional).
• Wire «10» (Brown-white) (INP3)
— Factory setting is «Front hood limit
switch». This wire connects to appropriate wire that becomes grounded when
the front hood opens. This input is multipurpose, it can operate in accordance
with selected logic.
• Wire «11» (Orange-black) («CAN1-Low»)
— It connects to appropriate
CAN-Low wire of the car.
• Wire «12» (Yellow-black) («CAN2-Low»/CH5)
— Factory setting is
«Close central lock». A negative impulse of 0,8 seconds is formed on the wire
to close central lock. Logic of the channel’s operation can be set in the table
of system outputs. When the car model code with support for CAN2-bus is
selected, channel CH5 stops to operate as an output.
• Wire «13» (Blue-black) (CH3)
— Factory setting is «N.O. Blockage». This
wire is used to control blocking relay with a normally open logic (it becomes
grounded when switching on the ignition and security system is armed).
Negative output of additional channel,maximum load current is 200 mA. This
output is multipurpose, it can operate in accordance with selected logic.
• Wire «14» (Yellow) (INP2)
— Factory setting is «Ignition». This wire
connects to ignition switch or to appropriate wire where 12V voltage appears
when ignition is switched on. This input is multipurpose, it can operate in
accordance with selected logic
• Wire «15» (Purple) (CH6)
— Factory setting is «Siren». It connects to
siren control wire (+).This output is multipurpose, it can operate in accordance
with selected logic (maximum load current is 2A).
• Wire «16» (Red) («Power supply» +12V)
— It should be connected to
reliable conductor with constant voltage of 12V.
