background image

11

Periodic inspections shall be conducted.

Rust on the metal parts or screws may cause a 
fall  of  this  product  resulting  in  injury  or  acci-
dents.
Consult the dealer for the inspections.

Do not use this product in an inflammable 
atmosphere.

Failure to observe this may cause an explosion 
resulting in injury.

Avoid installing this product in the loca-
tions where salt damage occurs or corro-
sive gas is produced.

Otherwise,  the  mounting  portions  will  deterio-
rate and accidents such as a fall of the product 
may occur.

The measures of protection against a fall 
of this product shall be taken.

Failure to observe this may cause a drop result-
ing in injury.
Be sure to install the safety wire.

The exclusively designed mount bracket 
shall be used.

Failure to observe this may cause a drop result-
ing in injury or accidents.
Use the exclusively designed mount bracket for 
installation.

Do not install this product in locations 
subject to vibration.

Loosening  of  mounting  screws  or  bolts  may 
cause a fall of the product resulting in injury.

Install this product in a location high 
enough to avoid people and objects from 
bumping the product.

Failure to observe this may cause a drop result-
ing in injury or accidents.

Do not strike or give a strong shock to this 
product.

Failure to observe this may cause fire or injury.
     

Turn the power off when do wiring of this 
product.

Failure  to  observe  this  may  cause  electric 
shock. In addition, short circuit or wrong wiring 
may cause fire.

Do not rub the edges of metal parts with 
your hand.

Failure to observe this may cause injury.

Turn the power off when cleaning this 
product.

Failure to observe this may cause injury.

[Precautions for use]

This product is designed to be used 
indoors. The product is not operable out-
doors.

This product has no power switch.

When  turning  off  the  power,  turn  off  a  circuit 
breaker.

To keep on using with stable performance

Do not use this product in hot and humid con-
ditions  for  a  long  time.  Failure  to  observe  this 
causes component degradation resulting in life 
shortening of the product.
Do  not  expose  this  product  to  direct  heat 
sources such as a heater.

Handle this product with care.

Do  not  drop  this  product,  nor  apply  shock  or 
vibration to the product. Failure to observe this 
may cause trouble.

About the PC monitor

When displaying the same image on the moni-
tor  for  a  long  time,  the  monitor  may  be  dam-
aged. It is recommended to use a screen-sav-
er.

When an error is detected, this product 
will restart automatically.

This  product  will  be  inoperable  for  around  2 
minutes after the restart just as when the power 
is turned on.

Summary of Contents for WV-SP105





































Reviews: