background image

9

Do not insert any foreign objects. 

Fire or electrical shock may be caused if water 
or any foreign objects, such as metal objects, 
enter inside the unit.
Turn the power off immediately and contact 
qualified service personnel for service. 

Do not use this product in an inflammable 
atmosphere. 

Failure to observe this may cause an explosion 
resulting in injury. 

Avoid installing this product in the loca-
tions where salt damage occurs or corro-
sive gas is produced.

Otherwise, the mounting portions will deterio-
rate and accidents such as a fall of the product 
may occur.

Do not strike or give a strong shock to this 
product.

Failure to observe this may cause fire or injury.

Keep SDXC/SDHC/SD memory cards 
away from infants and children.

Otherwise, they may swallow the cards by 
mistake.
In this case, consult a doctor immediately.

Do not hang down from this product or 
use this product as a pedestal. 

Failure to observe this may cause a drop 
resulting in accidents. 

Do not damage the power cable. 

Do not damage, fabricate, twist, stretch, bun-
dle, or forcibly bend the power cable. Do not 
place heavy objects on it, and keep it away 
from heat sources. 
Use of a damaged power cable may cause 
electric shock, short circuit, or fire. 
Consult the dealer for repair.

Do not attempt to disassemble or modify 
this product. 

Failure to observe this may cause fire or electric 
shock. 
Consult the dealer for the repair or inspections. 

Do not install or clean the camera, or 
touch this product, the power cable or the 
connected cables during thunder storms.

Failure to observe this may cause electric shock.

Refer installation work to the dealer. 

Installation work requires technique and experi-
ence. Failure to observe this may cause fire, 
electric shock, injury, or damage to the product. 
Be sure to consult the dealer. 

Stop the operation immediately when 
something is wrong with this product. 

When smoke goes up from the product, the 
smell of smoke comes from the product, or the 
exterior of the product has deteriorated, con-
tinued use will cause a fire or fall of the product 
resulting in injury, or damage to the product. 
In this case, turn the power off immediately and 
contact qualified service personnel for service.

Select an installation area that can sup-
port the total weight. 

Selecting an inappropriate installation surface 
may cause this product to fall down or topple 
over, resulting in injury or accidents.
Installation work shall be started after sufficient 
reinforcement. 

Periodic inspections shall be conducted. 

Rust on the metal parts or screws may cause a 
fall of the product resulting in injury or acci-
dents. 
Consult the dealer for the inspections. 

The exclusively designed mount bracket 
shall be used.

Failure to observe this may cause a drop 
resulting in injury or accidents.
Use the exclusively designed mount bracket for 
installation.

Precautions

Summary of Contents for WV-S4550L

































Reviews: