background image

2

CONTENTS

Preface ....................................................................................................................................... 2

Precautions ................................................................................................................................ 2

Major Operating Controls and Their Functions  .......................................................................... 4

Installations ................................................................................................................................ 5

Specifications ................................................................................................................ back cover

Standard Accessories ................................................................................................... back cover

Precautions

• Refer installation work to the dealer.

Installation work requires technique and experiences. Failure to observe this may cause
fire, electric shock, injury, or damage to the product. Be sure to consult the dealer.

• Avoid installing this bracket in the locations where salt damage occurs or corrosive

gas is produced.

Otherwise, the mounting portions will deteriorate and accidents such as a fall of the camera
may occur.

• Use only the specified camera.

Failure to observe this may cause a fall of an inappropriate camera resulting in injury or
accidents. Refer to the catalog or the installation guide of the camera for supported cam-
eras.

• The screws and fixation mechanisms shall be tightened securely.

Failure to observe this may cause a fall of the camera resulting in injury.

• The measures of protection against a fall of the camera shall be taken.

Failure to observe this may cause injury. Be sure to install the safety wire.

Preface

This ceiling mount bracket is exclusively designed to mount the network camera on a ceiling.
Refer to the catalog or the installation guide of the camera for supported cameras.
This bracket can be used for an area with weak pull-out strength such as plasterboard in a
double ceiling.
This bracket is an embedded type to reduce the exposed portion of the camera body.

• WV-Q155C: Clear dome cover
• WV-Q155S: Smoked dome cover (approx. 50 % of transmittance)

Summary of Contents for WV-Q155C













Reviews: