Panasonic WV-CW590G Operating Instructions Manual Download

Page: 24 / 31

3. Move the cursor to ALARM IN 2, and then tilt the

joystick left and right to select the operation the
camera should perform when an external signal is
received by ALARM IN 2.

OFF

Ignore alarm input signals.

2POSI

Move to preset position 2.

SEQ

Start sequential movement.

PATROL2

Start PATROL 2.

AUTOTRACK2 :

Move to preset position number 2,

and then perform auto tracking.

PATROL2 (S) :

Start PATROL 2, and maintain the

stored picture quality settings
(page 17) even after completion.

The factory default setting is OFF.
4. Move the cursor to ALARM IN 3, and then tilt the

joystick left and right to select the operation the
camera should perform when an external signal is
received by ALARM IN 3.

OFF

Ignore alarm input signals.

3POSI

Move to preset position 3.

SORT

Start sort movement.

PATROL3

Start PATROL 3.

AUTOTRACK3 :

Move to preset position number 3,

and then perform auto tracking.

PATROL3 (S) :

Start PATROL 3, and maintain the

stored picture quality settings
(page 17) even after completion.

The factory default setting is OFF.
5. Move the cursor to ALARM IN 4, and then tilt the

joystick left and right to select the operation the
camera should perform when an external signal is
received by ALARM IN 4.

OFF

Ignore alarm input signals.

4POSI

Move to preset position 4.

Black and white display while

signal is being input.

PATROL4

Start PATROL 4.

AUTOTRACK4 :

Move to preset position number 4,

and then perform auto tracking.

PATROL4 (S) :

Start PATROL 4, and maintain the

stored picture quality settings
(page 17) even after completion.

The factory default setting is OFF.

Notes:

• Use PATROL 1 (S) to 4 (S) if you want to switch

picture quality (for example to switch picture

quality from day to night) when an alarm input is

received. ALARM IN4 can be used combined with

BW.

To use the camera with this application, set the

picture quality you want to switch before

registering the patrol, then start the patrol

registration and then end the registration

immediately.

• If you want to change the picture quality settings

according to alarm input for PATROL 1 (S) to 4 (S),

the settings are applied to the camera settings

and are kept even after the camera is turned on

again.

• PATROL1(S)-4(S) displays only the set number of

patrol routines (page 17).

6. Move the cursor to CNT-CLS 1, and then tilt the

joystick left and right to select the alarm output that
should be performed over ALARM OUT 1 when an
alarm is detected.

OFF

No alarm output

AUX1

Output a contact close signal when

AUX1 input is received from the system
controller.

ALARM :

Output an alarm signal when an alarm is

detected by the motion detector (page 22)
or the preset alarm (page 23). After
selecting this setting, perform step 7 to
specify the alarm signal output time.

The factory default setting is OFF.
7. Move the cursor to TIME OUT and then tilt the

joystick left and right to select the alarm signal
output time.

Tilting the joystick cycles through the output time

display in the sequence shown below. (unit: ms)

The factory default setting is 100MS.

8.    Move  the  cursor  to  CNT-CLS  2,  and  then  tilt  the
joystick left and right to select the alarm output that
  should be performed from ALARM OUT 2 when an
alarm is detected.

OFF

No alarm output

AUX2

Output a contact close signal when

AUX2 input is received from the system
controller.

Output a contact close signal only while

the camera is in the black and white
mode.

The factory default setting is OFF.

9. Move the cursor to COAX ALM OUT, and then tilt

the joystick left or right to toggle it ON and OFF.

This setting turns alarm controls whether an alarm is

output when the camera moves to one of the preset