background image

21

 The "ZONE NUMBER" screen appears. 

Step 2

Move the cursor to the number at the right of the title and select the zone number using the 
right or left button. 

Step 3

Move the cursor to "POSITION" and press the [SET ] button. 

Step 4

Use the [UP], [dOwN], [RIghT], and [lEfT ] buttons to determine the left upper position of the 
zone to be set and press the [SET] button. 

Step 5

Use the [UP], [dOwN], [RIghT], and [lEfT ] buttons to determine the lower right position of the 
zone to be set and press the [SET] button. 

 An asterisk "*" will be displayed after the number and the zone setting will be saved. 

Step 6

when “ON (2)” is selected for “PRIVACY ZONE”, the mosaic level may be adjusted. The mosaic 
level may be set through “ZONE lEVEl”. (Range: 1 to 4) 

Note:

 

•  To delete a zone, select the zone number and press the [SET] button after moving the cur

-

sor to "dEl". 

  •  To change the settings of a zone, select the zone number and repeat from step 3. 

B

 Image stabilizer setting [STABILIZER]

whether or not to enable the image stabilizer is determined. 
This function is effective for the case that the camera is installed at a place with slight shaking. 
ON:  Enables the image stabilizer. 
OFF (default):  disables the image stabilizer. 

Important:

  •  When "ON" is selected for the image stabilizer, the view angle becomes narrower and the 

resolution becomes lower. when "ON" is selected for the image stabilizer, check the view 
angle and resolution at camera installation. 

  •  The image stabilizer function may not work for the following subjects.
    • Dark subject 
    • Less contrasty subject (e.g. white wall) 
    • Subject shaking at excessive speed  
    • Large amplitude image shaking

C

 Electronic zoom setting [EL-ZOOM] 

whether or not to use the electronic zoom is determined. 
ON:  Uses the electronic zoom. 
OFF (default):  does not use the electronic zoom. 

Summary of Contents for WV-CP300 Series





























Reviews: