23
English
The TV goes into Standby mode
●
Auto power standby function is activated.
The remote control does not work or is intermittent
●
Are the batteries installed correctly?
(p. 8)
●
Has the TV been switched on?
●
The batteries may be running low. Replace them with
new ones.
●
Point the remote control directly at the TV’s remote
control signal receiver (within about 7 m and a 30
degree angle of the signal receiver).
●
Situate the TV away from sunshine or other sources
of bright light not to shine on the TV’s remote control
signal receiver.
No image can be displayed
●
Check the TV is turned on.
●
Check the mains lead is plugged into the TV and the
socket outlet.
●
Check the correct input mode is selected.
●
Check the settings of the Picture Menu.
●
Check all required cables and connections are firmly
in place.
Unusual image is displayed
●
Turn the TV off with Mains power On / Off switch,
then turn it on again.
●
If the problem persists, initialise all settings.
[Shipping Condition] (p. 14)
There may be red, blue, green and black spots on
the screen
●
This is a characteristic of liquid crystal panels and is
not a problem. The liquid crystal panel is built with
very high precision technology giving you fine picture
details. Occasionally, a few non-active pixels may
appear on the screen as a fixed point of red, green,
blue or black. Please note this does not affect the
performance of your LCD.
Parts of the TV become hot
●
Even if the temperature of parts of the front, top and
rear panels has risen, these temperature rises do
not cause any problems in terms of performance or
quality.
The LCD panel moves slightly and clattered sound is
heard when it is pushed with a finger
●
There is a little gap around the panel to prevent
damage to the panel. This is not a malfunction.
Overcurrent error message appears
●
The connected USB device might cause this error.
Remove the device and turn the TV to standby mode
with Standby On / Off switch, then turn it on again.
●
Check foreign objects are not inside the USB port.
FAQs
Before requesting service or assistance, please follow
these simple guides to solve the problem. When an error
message appears, follow the message’s instructions. If
the problem still persists, contact your local Panasonic
dealer or the authorised service centre.
Block noise, frozen or disappearing image occurs
in Digital TV mode / White spots or shadow image
(ghosting) occurs in Analogue mode / Some
channels cannot be tuned
●
Check the position, direction and connection of the
aerial.
●
Check [Digital TV Signal Condition] (p. 15). If [Signal
Condition] is poor, check aerial.
●
Weather conditions will affect signal reception (heavy
rain, snow, etc.), in particular in poor reception areas.
Even during good weather, the high pressure can
cause poor reception of some channels.
●
Due to the digital reception technologies involved,
quality of the digital signals may be relatively low in
some cases, despite good reception of analogue
channels.
●
Consult your local dealer or service provider for the
availability of services.
Picture quality problem
●
Check the settings of the Picture Menu.
●
Set [Noise Reduction] to remove noise (p. 11).
●
Check nearby electrical products (car, motorcycle,
fluorescent lamp).
●
Reset channels.
●
Check that the output of the external equipment
matches the input of the TV. When connecting with
SCART, ensure the output setting of the external
equipment is not S-Video.
Sound quality problem
●
Check the volume level or sound mute.
●
Check connections and setting of external equipment.
●
Sound signal reception may be deteriorated.
●
Set [MPX] to [Mono] (p. 13).
Picture or sound problems with HDMI connection
●
Check the HDMI cable is connected properly.
●
Turn the TV and equipment off, then turn them on
again.
●
Check an input signal from the equipment.
●
Use equipment compliant with EIA/CEA-861/861D.
●
Set the sound setting of the connected equipment to
“2ch L.PCM”.
●
Check the [HDMI Input] setting (p. 13).
●
If digital sound connection has a problem, select
analogue sound connection.
The TV does not switch on
●
Check the mains lead is plugged into the TV and the
socket outlet.
TH-60A430A_Z.indb 23
TH-60A430A_Z.indb 23
3/20/2014 2:38:59 PM
3/20/2014 2:38:59 PM
