FAQs, etc.
•
Speci
fi
cations
•
Frequently Asked
Questions
Power Source
AC 220-240 V, 50 / 60 Hz
Power
Consumption
Average use
255 W
Standby condition
0.7 W
Display
panel
Aspect Ratio
16:9
Visible screen size
106 cm (diagonal)
922 mm (W) × 518 mm (H)
Number of pixels
786,432 (1,024 (W) × 768 (H))
[3,072 × 768 dots]
Sound
Speaker
160 mm × 42 mm × 2 pcs, 8
Ω
Audio Output
20 W (10 W + 10 W), 10% THD
Headphones
M3 (3.5 mm) stereo mini Jack × 1
Receiving Systems /
Band name
PAL I
UHF E21-68 / VHF Ireland channel
PAL 525/60
Playback of NTSC tape from some PAL Video recorders (VCR) or
NTSC disc playback from DVD player and recorder.
M.NTSC
Playback from M. NTSC Video recorders (VCR).
NTSC (AV input only)
Playback from NTSC Video recorders (VCR).
Aerial - Rear
VHF / UHF
Operating Conditions
Temperature
: 0 °C - 35 °C
Humidity
: 20 % - 80 % RH (non-condensing)
Connection T
erminals
AV1 (Scart terminal)
21 Pin terminal (Audio/Video in, Audio/Video out, RGB in, Q-Link)
AV2 (Scart terminal)
21 Pin terminal (Audio/Video in, Audio/Video out, RGB in, S-Video in, Q-Link)
AV3
VIDEO
RCA PIN Type × 1
1.0 V[p-p] (75
Ω
)
S-VIDEO
Mini DIN 4-pin
Y:1.0 V[p-p] (75
Ω
) C:0.286 V[p-p] (75
Ω
)
AUDIO L - R
RCA PIN Type × 2
0.5 V[rms]
COMPONENT
VIDEO
Y
1.0 V[p-p] (including synchronization)
P
B
, P
R
±0.35
V[p-p]
AUDIO L - R
RCA PIN Type × 2
0.5 V[rms]
HDMI1 / 2
TYPE A Connectors
•
This TV supports “HDAVI Control 3” function.
Output
AUDIO L - R
RCA PIN Type × 2
0.5 V[rms] (high impedance)
Dimensions ( W × H × D )
1,020 mm × 727 mm × 327 mm (With Pedestal)
1,020 mm × 679 mm × 92.5 mm (TV only)
Mass
27.5 k Net (With Pedestal)
25.5 k Net (TV only)
43
Problem
Actions
HDMI
The remote control
does not work
•
Are the batteries installed correctly? (p. 6)
•
Has the TV been switched On?
TV goes into
“Standby mode”
•
Off Timer function is activated.
•
The TV enters “Standby mode” about 30 mins. after broadcasting
ends.
Pictures from external
equipment are unusual
when the equipment is
connected via HDMI
•
Is the HDMI cable connected properly? (p. 38)
•
Turn Off the TV and equipment, then turn them On again.
•
Check an input signal from the equipment. (p. 41)
•
Use an equipment compliant with EIA/CEA-861/861B.
Sound is unusual
•
Set the sound setting of the connected equipment to
“2ch L.PCM”.
•
Check the “HDMI1 Input” setting in the Sound Menu. (p. 22)
•
If digital sound connection has a problem, select analogue sound
connection. (p. 40)
Other
Speci
fi
cations
Note
•
Design and Speci
fi
cations are subject to change without notice. Mass and Dimensions shown are approximate.
•
This equipment complies with the EMC standards listed below.
EN55013, EN61000-3-2, EN61000-3-3, EN55020.
•
Pedestal: ST-42R4-WK (For safety approval)
FAQs
