Panasonic VB-44210G User Manual Download Page 64

Page: 64 / 394

Chapter 3. System Features

Section 700 - Operation

Page 3-18

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

DID Delayed Ringing

(CPC-B Version 5.0 or higher)

Description

For a description of this feature, see “DID/DNIS Flexible Ring Assignments”
on page 3-18.

DID/DNIS Flexible Ring Assignments

(CPC-B Version 5.0 or higher)

Description

DID/DNIS Flexible Ring Assignments allow night ringing and delayed
ringing for specific DID/DNIS numbers.

Related Programming

• FF1 (System): Delayed Ring

• FF1 (System): Central Office Delayed Ring Timer

• FF1 (System): Inbound DID Dial Numbers

• FF1 (System): DNIS Number Setting

Considerations

• Timing for DID/DNIS delayed ringing is controlled by the Central Office

Delayed Ring Timer.

• The system uses a DID Numbers Table for DID assignment. The DID

Numbers Table allows up to 500 DID assignments. Each assignment
consists of the DID number and an associated extension.

• The system uses a separate DNIS Numbers Table for DNIS assignment.

The DNIS Numbers Table allows up to 500 DNIS assignments, with each
assignment consisting of the DNIS number and an associated extension.

• When multiple extensions are assigned delayed ringing for the same DID/

DNIS number, unanswered delay ringing forwards based on the extension
with the lowest port number.

For example, if port numbers 125 and 126 both have delayed ringing for the

Summary of Contents for VB-44210G











































































































































































































































































































































































































Search results

Summary of Contents for VB-44210G

Reviews:

Related manuals for VB-44210G

Brands by name

Popular brands

Panasonic VB-44210G, User Manual

Search results

Summary of Contents for VB-44210G

Reviews:

Related manuals for VB-44210G

Brands by name

Popular brands