Panasonic VB-44210G User Manual Download Page 269 | Manualshive

Page: 269 / 394

background image

Section 700 - Operation

Chapter 6. SLT Features

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

6-13

Related Programming

• FF1 (System): Extension Class of Service Setting (CPC-AII and CPC-B

3.1 or higher)

• FF3 (Extension): Extension Class of Service Assignment (CPC-AII and

CPC-B Version 3.1 or higher)

Considerations

• If more than one caller is attempting to reach the ringing extension, the

Direct Call Pickup feature will answer the call that arrives first.

Once the call has been picked up, other extensions that attempt to pick up
the call receive busy tone.

• You can answer incoming calls, intercom calls (both tone and voice), call

waiting, paging, transferred calls, or recalls using the Direct Call Pickup
feature. You cannot answer camp-on callback rings with this feature.

Group Call Pickup

Description

Using the Group Call Pickup feature, you can answer calls to other extensions
within your Paging Group (01-07) without entering the number of the ringing
extension.

Operation

1. Lift the handset.

2. Dial

“70.”

Related Programming

• FF1 (System): Extension Class of Service Setting (CPC-AII and CPC-B

Version 3.1 or higher)

• FF3 (Extension): Extension Class of Service Assignment (CPC-AII and

CPC-B Version 3.1 or higher)

• FF3 (Extension): Extension Page Group

«
...
267
268
269
270
271
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: Bang & Olufsen Pages: 2

Brand: Bang & Olufsen Pages: 20

Brand: Bang & Olufsen Pages: 24

BeoSound Ouverture

Brand: Bang & Olufsen Pages: 44

Brand: Jensen Pages: 2

Brand: GE Pages: 100

Brand: AT&T Pages: 12

Brand: TransTel Communications Pages: 48

Brand: Radio Shack Pages: 16

Brand: Fender Pages: 51

myPhone Jazz 202112

Brand: mPTech Pages: 65

Brand: ETS Pages: 2

Brand: Denver Pages: 27

Brand: Net2Phone Pages: 20

Brand: Oaxis Pages: 21

Brand: Dictaphone Pages: 24

Brand: Trevi Pages: 24

PROLIGHTS BlackBoxF1G4

Brand: Music & Lights Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands