Panasonic VB-44210G User Manual Download Page 250 | Manualshive

Page: 250 / 394

background image

Chapter 5. DSLT Features

Section 700 - Operation

5-32

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

• If the transferred call is not answered immediately, it will queue for a

specified time and then return to the extension sending the OHVA. (The
recall time is set in the Transfer-Recall Timer.)

• You cannot receive a Call Waiting message during an OHVA.

• You cannot toggle back and forth between two calls during an OHVA.

Onhook Dialing

(All Versions)

Description

To use onhook dialing, press the

ON/OFF

key.

The DSLT does not have a microphone, so the user must lift the handset to
talk.

Pooled Trunk Access

(All Versions)

Description

The DBS system is designed to accept from 8 to 64 outside lines. These lines
can be divided into seven Pooled Trunk groups. The groups are numbered 9
and 81-86.

To select a free outside line, choose a pooled trunk group number. The DBS
automatically selects a free line from the group.

Operation

1. Lift the handset.

The phone issues an intercom dial tone.

2. Dial the desired trunk group number (81-86 or 9).

3. Dial the outside number.

Related Programming

• FF1 (System): Least Cost Routing (LCR) Access

«
...
248
249
250
251
252
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: 2N Pages: 23

Brand: Xblue Networks Pages: 52

Brand: AT&T Pages: 71

BeoSound 3000 2671

Brand: Bang & Olufsen Pages: 68

Clarity Extra W1100

Brand: Walker Pages: 27

Brand: Gigaset Pages: 15

Brand: vitapur Pages: 36

Brand: VTech Pages: 2

Brand: Plantronics Pages: 2

Brand: AT&T Pages: 15

Brand: Flying Voice Pages: 64

Brand: Zazen Pages: 8

Brand: Daewoo Pages: 29

Brand: VTech Pages: 81

Brand: BEATFOXX Pages: 16

Brand: Swisscom Pages: 110

Brand: Uniden Pages: 28

Brand: DAPAudio Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands