12
English
Parts used to assemble the wall-hanging bracket
ヂ
Base upper and lower
fitting (2)
ッ
Bracket base left fitting
(1)
ツ
Bracket base right fitting
(1)
4
ヅ
Screw for assembling
the fixture (8)
M5×10
Parts used for installation
View of fully assembled fixture
R
L
㇙
Allen head countersunk screw (4)
M8×32
㇜
Screw for securing unit (2)
M5×100
㇚
Dished toothed washer (4)
㇝
Allen wrench (included tool) (1)
㇛
Insulation spacer (4)
] The images shown in this manual are for illustrative purpose only.
] The product specifications may be changed at any time without prior notice.
Precautions for wall-hanging bracket fitting
] The wall-hanging bracket is for use in attaching a plasma display unit to a vertical wall for viewing.
Do not fit to any surface other than a vertical wall.
] To ensure correct plasma display performance and prevent trouble, do not fit at any of the following locations.
• Near sprinklers or fire/smoke detectors
• Where there is a risk of exposure to vibration or impact
• Near high-voltage wires or dynamic power supplies
• Near sources of magnetism, heat, water vapor or soot
• Locations exposed to air blown from heating equipment
• Where droplets of condensation from an air conditioner or other unit may form
] Fit using techniques suited to the structure and materials of the fitting location.
] Use commercially available screws with a nominal diameter of 6 mm (0.2 inches) that are suited to the wall
material (wood, steel frame, concrete etc.) you are fitting the bracket to.
] Ensure good air flow so that the ambient temperature does not exceed 40 °C (104 °F).
Failure to do this may cause heat to build up inside the plasma display, resulting in malfunction.
] Spread a soft blanket or cloth over the floor so that the plasma display and floor will not be marked or scratched
during the assembly and installation work.
] When screwing down the parts, ensure that the screws are neither insufficiently tightened nor over tightened.
] For the plasma display power supply plug, use a power supply outlet that can be reached easily.
] Take sufficient care and ensure safety around you when performing the installation work.
] Do not install the plasma display underneath ceiling lamps (spotlights, halogen lamps, etc.).
Otherwise, the cabinet may be bent or damaged by high heat.
To the Installation Contractor
] If the wall-hanging bracket installation and display installation work are performed by different contractors, please
ensure that this instruction manual is passed from the wall-hanging bracket installation contractor to the display
installation contractor after the wall-hanging bracket installation work is complete.
] Please give this instruction manual to the customer after the installation work is completed.
Components
Summary of Contents for TY-WK65PR20
