manualshive.com logo in svg

Panasonic Section 700, User Manual

Discover the Panasonic Section 700 User Manual - providing comprehensive instructions for optimal utilization. Easily download this manual for free from manualshive.com, enabling you to navigate through all features, troubleshoot efficiently, and fully unlock the potential of your Panasonic Section 700 device.

Share
Download
background image

Section 700 - Operation

Chapter 2. Attendant Features

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

  2-21

the personal VM key is not assigned to the lowest-numbered key, it will not 
flash to indicate VM messages.

Station Lockout Code Assignment

 (All Versions)

Description

The Station Lockout feature allows users to dial a Station Lockout code to 
restrict their phone from being used for outside calls.

Station Lockout codes can be assigned through the attendant phone.

Operation

To program a Station Lockout code:

1. Press 

the 

ON/OFF

 key.

• The phone issues intercom dial tone.

• The 

ON/OFF

 LED lights.

2. Press 

the 

CONF

 key.

3. Dial 

“#8.”

4.  Dial the extension number.

5.  Enter the desired key code (four digits).

6. Press 

the 

HOLD

 key.

“STORE XXXX” (where “XXXX” is the key code) appears on the 
display.

7. Press 

the 

ON/OFF

 key.

The 

ON/OFF

 LED goes off.

Considerations

• A locked extension can be used for Intercom Calls.

• Station Lockout key codes can also be set through system programming.

Summary of Contents for Section 700











































































































































































































































































































































































































Reviews:

No comments

Related manuals for Section 700

Samsung SMT-i5343 Manual preview
SMT-i5343
Brand: Samsung Pages: 125
TCL T550 Manual preview
T550
Brand: TCL Pages: 55
Aastra Clearspan 6731i Admin Manual preview
Clearspan 6731i
Brand: Aastra Pages: 8
Aastra AASTRA 9133 I Administrator'S Manual preview
AASTRA 9133 I
Brand: Aastra Pages: 37
Aastra 6865i Quick Reference Manual preview
6865i
Brand: Aastra Pages: 3
Aastra 6863i Quick Start Manual preview
6863i
Brand: Aastra Pages: 2
Aastra 55I Manual preview
55I
Brand: Aastra Pages: 15
Aastra 55I Training preview
55I
Brand: Aastra Pages: 22
Aastra 55I Release Notes preview
55I
Brand: Aastra Pages: 44
Aastra 5361 Quick User Manual preview
5361
Brand: Aastra Pages: 24
Aastra 51i User'S Quick Start Manual preview
51i
Brand: Aastra Pages: 2
Aastra 6735i Quick Reference Manual preview
6735i
Brand: Aastra Pages: 3
Aastra 6700i Series Instruction Manual preview
6700i Series
Brand: Aastra Pages: 29
Aastra AastraLink Pro 160 User Manual preview
AastraLink Pro 160
Brand: Aastra Pages: 230
Aastra 6735i Release Notes preview
6735i
Brand: Aastra Pages: 45
Aastra 6737i User Manual preview
6737i
Brand: Aastra Pages: 112
8x8 Inc 675xi Series User'S Reference Manual preview
675xi Series
Brand: 8x8 Inc Pages: 47
Aastra 6737i Quick Reference Manual preview
6737i
Brand: Aastra Pages: 2

Brands by name

Popular brands

Load more brands