SQT1211
5
8
Mode indicator (amber)
9
[SC-ALL6]
Rear surround indicator (blue/green)
10 AUX indicator (yellow)
11 Bluetooth
®
indicator (blue)
12 Network indicator (blue/red)
13 Operation indicator (amber)
14 LAN terminal
15 AC IN terminal
16 AUX IN terminal
§
1 These switches work just by touching the marks. Each
time you touch the switch, there will be a beep sound.
The beep sound can be set to off. (
l
19)
§
2 Screw holes (used only to place the product on display
at retailers)
Blinks once
≥
The following setting is turned on.
“Network standby” (
l
9)
“Bluetooth
®
standby” (
l
15)
“Automatic updates” (
l
18)
“Operation sound setting” (
l
19)
– When the setting is turned off, it blinks twice.
≥
Bluetooth
®
transmission mode is set to Mode 1.
(
l
16)
≥
Bluetooth
®
input level is set to Low. (
l
16)
≥
AUX input level is set to Normal. (
l
16)
Blinks twice
≥
Bluetooth
®
transmission mode is set to Mode 2.
(
l
16)
≥
Bluetooth
®
input level is set to Middle. (
l
16)
≥
AUX input level is set to High. (
l
16)
Blinks thrice
≥
Bluetooth
®
input level is set to High. (
l
16)
Blinks
≥
It may blink when the unit turns to standby mode.
– Do not disconnect the AC mains lead. Doing so
may cause malfunction or damage.
Blinks slowly
≥
The unit is during the update process. (
l
18)
≥
The mode indicator also blinks when the volume is
changed.
Lights up (green)
≥
The pairing as the left surround speaker is
successful.
Lights up (blue)
≥
The pairing as the right surround speaker is
successful.
Blinks slowly (green)
≥
The unit is waiting for the rear surround connection.
Blinks (green)
≥
The unit is waiting for pairing.
Blinks fast (green)
≥
The unit is ready for pairing as the left speaker.
Blinks fast (blue)
≥
The unit is ready for pairing as the right speaker.
Lights up
≥
AUX is selected as the audio source. (
l
16)
Lights up
≥
The pairing as the Bluetooth
®
speaker is successful.
Blinks slowly
≥
The unit is waiting to connect.
Blinks fast
≥
The unit is ready for pairing.
Blinks alternately (blue/red)
≥
The unit is carrying out an internal process.
– Wait for approximately 60 seconds before the
blinking stops.
– Do not disconnect the AC mains lead. Doing so
may cause malfunction or damage.
Lights up (blue)
≥
The unit is connected to the network.
Blinks slowly (blue)
≥
The unit is ready for network setup. (
l
7)
Blinks (blue)
≥
The unit is waiting for the WPS connection. (
l
9)
Blinks fast (blue)
≥
The unit is waiting for the WPS PIN code
connection. (
l
9)
Blinks (red)
≥
The unit is connecting to the network.
– When the network connection cannot be
established, the blinking keeps going. Check the
network connection. (
l
7)
≥
The volume cannot be changed during the network
indicator blinking blue.
Blinks once
≥
The unit detects the switch touched.
Blinks twice
≥
The unit detects a valid operation performed by
touching and holding the switch.
Blinks
≥
Automatic standby mode is activated. (
l
6)
SC-ALL9&6-SQT1211_mst.book 5 ページ ２０１６年１月１２日 火曜日 午後３時１６分
