8
RQT0A22
9
Select “Connect” to apply the settings.
≥
On the unit’s display, “SUCCESS” appears when the
connection is established. (The network indicator “
”
lights up.)
– If “FAIL” is displayed press [OK], check the network
name (SSID) and the password, and then try the
setting again.
≥
Depending on the device, the connection complete
screen may not be displayed.
10
Make sure to connect your compatible device back
to your home wireless network.
≥
Enable Java and Cookies in your browser settings.
1
Press [RADIO/EXT-IN]
on the remote control
repeatedly to select “NETWORK”.
2
To enter “WPS PUSH” mode
1 Press [SETUP] on the remote control repeatedly to
select “NET SETUP” and then press [OK].
“WPS PUSH” is indicated on the display.
2 Press [OK].
≥
Alternatively, touch and hold [
5
/
9
] on the unit for
at least 4 seconds.
“WPS” flashes on the display.
3
Activate the WPS button on the wireless router.
≥
On the unit’s display, “SUCCESS” appears when the
connection is established. (The network indicator “
”
lights up.)
– "FAIL" may be displayed if the connection was not
made within the set time limit. Try the setting again. If
"FAIL" is still displayed, try other methods.
4
Press [OK] on the remote control to exit the
setting.
∫
Using the WPS PIN code
1
Press [RADIO/EXT-IN]
on the remote control
repeatedly to select “NETWORK”.
2
To enter “WPS PIN” mode
1 Press [SETUP] on the remote control repeatedly to
select “NET SETUP” and then press [OK].
2 Press [
3
,
4
] on the remote control to select “WPS
PIN” and then press [OK].
≥
Alternatively, touch and hold [
:
/
6
] on the unit for
at least 4 seconds.
The PIN code is indicated on the display.
3
Enter the PIN code into the wireless router.
≥
Once the system enters WPS PIN code mode, you cannot
set up using the WPS button. To use the WPS button, turn
the system off and then on, and redo the network settings.
≥
Depending on a router, other connected devices may
temporarily lose their connection.
≥
For details, refer to the operating instructions of the wireless
router.
1
Disconnect the AC mains lead.
2
Connect the unit to a broadband router, etc. using
a LAN cable.
3
Connect the AC mains lead to the unit and turn
this system on.
≥
When the connection is established, the network
indicator “
” lights up.
≥
Use category 5 or above straight LAN cables (STP) when
connecting to peripheral devices.
≥
The LAN cable must be connected or disconnected while the
AC mains lead is disconnected.
≥
Inserting any cable other than a LAN cable in the LAN port
can damage the system.
≥
If the LAN cable is disconnected, the network-related
settings (
l
9) will be initialized. In that case, make the
settings again.
≥
When a LAN cable is connected, the Wi-Fi function will be
disabled.
Method 2:
Using WPS (Wi-Fi Protected Setup
TM
)
A compatible wireless router may have the WPS
identifier mark.
●●●●●●●●
e.g.,
Wired LAN connection
Method 3:
Using a LAN cable
ロモワ
ドヒパャモヴユノヵバ
ヒパパャモヴユノヵヹナ
LAN cable
(not supplied)
Broadband router, etc.
e.g.,
SC-ALL5CD-EGEBGN~RQT0A22.book 8 ページ ２０１５年７月１７日 金曜日 午前１１時３０分
